07-11-2002
Modem
Hi... Thanks for all your help!
I have found the problem. Modem has conflict address. What i did was, i went into CMOS setup and change serial port from IRQ4 to IRQ3 and voala..... The modem is working fine now.
Again, thank you for all your help.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi everyone
I am having some real difficulties getting a dial in modem to work on one of my HP boxes. It's a mux modem on port 7 which I have set up at 9600 baud.
I can dial in, the handshakes are completed, but then it returns incoherent characters on the emulation screen. I think my dial in... (1 Reply)
Discussion started by: alwayslearningunix
1 Replies
2. UNIX for Advanced & Expert Users
I've spent enough time trying to put on work Lucent Winmodem in my armada M300 (compaq laptop) I use Mandrake 8.0 but as soon as i get connected
and prompmts appears modem shutsdown.
Does any one had a similar situation, solved it?
cheers (2 Replies)
Discussion started by: alex blanco
2 Replies
3. UNIX for Dummies Questions & Answers
Hi!
I have a little prob with dialing up to the internet... When I try connect, it says "Sorry, modem is busy"...
Specs:
Laptop
56K modem
Slackware 8.0
Kernel 2.4.5
Cheers;) (4 Replies)
Discussion started by: satan404
4 Replies
4. UNIX for Dummies Questions & Answers
Specs:
Dlink DFE-560EL external modem.
RedHat 7.1
How do you turn off the modem volume? I am getting annoyed of it beeping everytime I use it but there is no switch on the hardware to tune down the volume.
I have tried using minicom and use the following commands:
ATL0
ATM0
Next, I... (2 Replies)
Discussion started by: arz
2 Replies
5. UNIX for Dummies Questions & Answers
I have got Suse 8.0 by using a modem (US Robotics 56K Faxmodem Ext).
During connection i got the error 16. I tried it under RedHat and Mandrake too.....same problem. What can i do ?
Thanx...a lot...
Logfile:
SuSE Meta pppd (smpppd), Version 0.73 on zuhause.
wwwoffle not is running ... (1 Reply)
Discussion started by: Pennywize
1 Replies
6. UNIX for Dummies Questions & Answers
Ok. I tried following the directions from some of the other threads, but I've hit a road block.
I have red hat 7.3 and I installed the hcf package:
hcfpcimodem-0.99lnxtbeta03042700k2.4.18_3-1rh.i386.rpm
It installed ok, no errors, but I still can't get linux to find my modem. I've tried... (2 Replies)
Discussion started by: lawadm1
2 Replies
7. UNIX for Dummies Questions & Answers
Im using Kinternet with a Lucent modem on Suse 9.0
Ive installed the ltmodem driver and suse says the device is ready and configured. Ive configured it at /dev/ttyS0
This is the log that Kinternet gives after trying to connect:
SuSE Meta pppd (smpppd-ifcfg), Version 1.06 on linux.
Status... (0 Replies)
Discussion started by: Synbios
0 Replies
8. Solaris
Hi all,
Is there any difference between a null modem cable or a modem cable ?
i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup.
please correct if i am wrong,
thks (2 Replies)
Discussion started by: waterbear
2 Replies
9. Solaris
hi folks,
i am looking for a analog modem to use it with a solaris9 sparc mashine. as far as i know, solaris communicates with the modem using AT-commands. so do i need a special modem for solaris or just a modem? i am open for everything. PCI-modem, seriell modem, usb modem. what are you using? i... (1 Reply)
Discussion started by: pressy
1 Replies
10. IP Networking
How to get information that where is my modem configured in /dev.
I have two modems configured in my device .. one is USB and other is PCI modem.. USB is detected as /dev/USB0. but how to see about PCI modem? (0 Replies)
Discussion started by: s123.radha
0 Replies
LEARN ABOUT DEBIAN
device::modem::log::file
Device::Modem::Log::File(3pm) User Contributed Perl Documentation Device::Modem::Log::File(3pm)
NAME
Device::Modem::Log::File - Text files logging plugin for Device::Modem class
SYNOPSIS
use Device::Modem;
my $box = Device::Modem->new( log => 'file', ... );
my $box = Device::Modem->new( log => 'file,name=/var/log/mymodem.log', ... );
...
DESCRIPTION
This is meant for an example log class to be hooked to "Device::Modem" to provide one's favourite logging mechanism. You just have to
implement your own "new()", "write()" and "close()" methods.
Default text file is "/var/log/modem.log". On Windows platforms, this goes into "%WINBOOTDIR%/temp/modem.log". By default, if the folder of
the log file does not exist, it is created.
This class is loaded automatically by "Device::Modem" class when an object is instantiated, and it is the default logging mechanism for
"Device::Modem" class.
Normally, you should not need to use this class directly, because there are many other zillions of modules that do logging better than
this.
Also, it should be pondered whether to replace "Device::Modem::Log::File" and mates with those better classes in a somewhat distant future.
REQUIRES
Device::Modem
EXPORTS
None
AUTHOR
Cosimo Streppone, cosimo@cpan.org
COPYRIGHT
(C) 2002 Cosimo Streppone, <cosimo@cpan.org>
This library is free software; you can only redistribute it and/or modify it under the same terms as Perl itself.
SEE ALSO
Device::Modem Device::Modem::Log::Syslog
perl v5.8.8 2005-04-30 Device::Modem::Log::File(3pm)