05-11-2001
I do have one other question about how I set up the gateway. Basically all I did was add the -GW to the hosts file after my ip address. then I used the route add default to manually add to the routing table , is this the correct way to do it?
8 More Discussions You Might Find Interesting
1. Programming
I am developing a Network Appliation to monitor computers in a network.
Specs are
App monitors the current web page viewed in each system
App also can shutdown the computer in the network
App can show all process run by each computer in the network
I am now confused how to start my... (2 Replies)
Discussion started by: valaparambil88
2 Replies
2. IP Networking
hello i have a ubuntu ssh server that i can acess from any of my comnputers but only if they are on the same wireless network as the server. i tested trhis my tehtehring my samsung blackjack to my windows partition and installing openssh to windows it works when windows is on the wireless but no... (1 Reply)
Discussion started by: old noob
1 Replies
3. UNIX for Advanced & Expert Users
I am going to take up a position in Data & Network Security.
I would need to write network shell scripts doing the following task:
Going to around 2000 servers and findout which groups has access to each servers and which ids are there in each group that has access.
I need to implement... (1 Reply)
Discussion started by: pinnacle
1 Replies
4. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
5. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
6. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
7. Red Hat
Hi,
I have 2 machines in production environment:
1. redhat machine for application
2. DB machine (oracle)
The application doing a lot of small read&writes from and to the DB machine.
The problem is that after some few hours the network from the application to the DB becomes very slow and... (4 Replies)
Discussion started by: moshesa
4 Replies
8. IP Networking
My son does homework on a school laptop. I was thinking about setting up a gateway on my home network, so that I can monitor web traffic and know if he is doing his homework without standing over his shoulder. Ideally I would like to use the Raspberry Pi Model b that I already have. However, I... (15 Replies)
Discussion started by: gandolf989
15 Replies
ping(8) System Manager's Manual ping(8)
Name
ping - send ICMP ECHO_REQUEST packets to network hosts
Syntax
/etc/ping [ options ] host [ datasize [ npackets ]]
Description
The DARPA Internet is a large and complex network of hardware connected together by gateways. The command utilizes the ICMP protocol's
mandatory ECHO_REQUEST datagram to elicit an ICMP ECHO_RESPONSE from a host or gateway. ECHO_REQUEST datagrams (pings) have an IP and ICMP
header, followed by a struct timeval, and then an arbitrary number of pad bytes used to fill out the packet. The length of the default
datagram 64 bytes, but this may be changed using the command-line option.
Typing ``ping host'' without any options will either report ``host is alive'' or ``no answer from host''. To get more statistics use the
-l option or one of the other options.
When using for fault isolation, it should first be run on the local host to verify that the local network interface is up and running.
Then, hosts and gateways further and further away should be pinged. The command with options sends one datagram per second and prints one
line of output for every ECHO_RESPONSE returned. No output is produced if there is no response. If an optional npackets is given, only
that number of requests is sent. Round-trip times and packet loss statistics are computed. When all responses have been received or the
program times out with npackets specified, or if the program is terminated with a SIGINT, a brief summary is displayed.
Options
-d Turns on SO_DEBUG flag on the socket.
-l Gives more statistics than if is used without options. Long output.
-r Bypasses the normal routing tables and sends directly to a host on an attached network. If the host is not on a directly-attached
network, an error is returned. This option can be used to ping a local host through an interface that has no route through it. For
example, after the interface was dropped by
-v Lists ICMP packets other than ECHO RESPONSE that are received. Verbose output.
Restrictions
This program is intended for use in network testing, measurement, and management. It should be used primarily for manual fault isolation.
Because of the load it could impose on the network, it is unwise to use during normal operations or from automated scripts.
See Also
netstat(1), ifconfig(8c)
ping(8)