Setting SSH port Post: 24162

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Setting com port questions

I have a piece of equipment, a Baytech RPC-3, that I need to communicate with through the com port. I normally use this equipment at home and am able to connect to it without problems using FC5 and minicom; I brought the equipment into work and cannot get my pc, using Suse 10 and minicom to...

2. AIX

ssh setting

I would like to implement the secure shell environment in order for me to close all telnet and ftp ports. 1) Anyone can assist to give me a steps of what to do so that I can implement the ssh on my AIX5.3 server. 2) Currently I have installed putty in my PC to replace telnet directly into the...

3. IP Networking

network speed not tale with the port setting

Hi all, one of my Sun Box facing the problem. The network port i had set to Auto-Negotiated and i had edited the /etc/system/ file in the Sun box as below: set hme:hme_adv_autoneg_cap=1 set hme:hme_adv_100fdx_cap=0 set hme:hme_adv_100hdx_cap=0 But when i checked the /var/adm/messages/, it...

4. Solaris

Setting up SSH - first time

Good day to you all. I have a server (running on SunOS 5.8) that i always got into via telnet. I have eventually decided to block telnet access to it and instead look toward using SSH. The problem is, whne i establish the SSH connection via PuTTy, i get the "Log in as" prompt, but upon...

5. IP Networking

Setting up port mirroring on LINUX

Hello everyone. I am supposed to configure port mirroring on Linux (the LAN traffic needs to be routed to the other interface and passed a copy to network monitoring software): eth0 - connected to local traffic eth1 - connected to the Internet The machine is running CentOS v4.4 (Server...

6. UNIX for Advanced & Expert Users

check remote switch port speed setting

Hi, Someone told me how to check the remote switch port's speed setting on the other end of the cable, from linux. I forgot it. Anyone knows? I checked dmesg, ethtool (haven't checked this out thoroughly) , no luck. thanks, Marc

7. IP Networking

Is there any way to add an exception for a port in the firewall setting, permanently?

Hello, I want to add a port in the firewall exception list so that my application can be accessed over network even if firewall is disabled. I am using iptables command to add exception. The problem is, after setting the rule if I change the firewall setting i.e. on/off then it is overwriting...

8. IP Networking

SSH Port Forwarding - sharing the same port

Hi Linux/Unix Guru, I am setting Linux Hopping Station to another different servers. My current config to connect to another servers is using different port to connect. e.g ssh -D 1080 -p 22 username@server1.com ssh -D 1081 -p 22 username@server2.com Now what I would like to have...

9. Red Hat

Setting serial port configuration

I have 1 serial port (9 Pin) attached with my Linux server.If I give $dmesg | grep tty , it provides me the following. ttyS0 and ttyS1. I have 1 COM port with my server mother board. I have 1 customized application that requires this COM port to be used. The parameter to be set for COM port...

10. Red Hat

Serial Port Setting Automatically changes

I am trying to change the setting of serial port baud rate in Red Hat Linux 5.9 by the following command. >> stty 9600 cs8 -parenb -ixon -cstopb -echo -F /dev/ttyS0 The serial port will be used by our custom application in 2 separate servers which are the replica of one another. The port setting...

LEARN ABOUT PHP

ssh-argv0

SSH-ARGV0(1)						    BSD General Commands Manual 					      SSH-ARGV0(1)

NAME

     ssh-argv0 -- replaces the old ssh command-name as hostname handling

SYNOPSIS

     hostname | user@hostname [-l login_name] [command]

     hostname | user@hostname [-afgknqstvxACNTX1246] [-b bind_address] [-c cipher_spec] [-e escape_char] [-i identity_file] [-l login_name]
     [-m mac_spec] [-o option] [-p port] [-F configfile] [-L port:host:hostport] [-R port:host:hostport] [-D port] [command]

DESCRIPTION

     ssh-argv0 replaces the old ssh command-name as hostname handling.	If you link to this script with a hostname then executing the link is
     equivalent to having executed ssh with that hostname as an argument.  All other arguments are passed to ssh and will be processed normally.

OPTIONS

     See ssh(1).

FILES

     See ssh(1).

AUTHORS

     OpenSSH is a derivative of the original and free ssh 1.2.12 release by Tatu Ylonen.  Aaron Campbell, Bob Beck, Markus Friedl, Niels Provos,
     Theo de Raadt and Dug Song removed many bugs, re-added newer features and created OpenSSH.  Markus Friedl contributed the support for SSH
     protocol versions 1.5 and 2.0.  Jonathan Amery wrote this ssh-argv0 script and the associated documentation.

SEE ALSO

     ssh(1)

Debian Project							 September 7, 2001						    Debian Project