07-04-2002
Newbie help needed connecting to Internet
I have an Ultra5 with 2.56 that is connected to a network. We don't use a proxy server on the network but access the internet directly through a gateway. How do I configure the Solaris box to see the internet?
Opening the internet explorer and setting HTTP; FTP etc ports to the ip of the gateway doesn't seem to work.
10 More Discussions You Might Find Interesting
1. IP Networking
I have installed Solaris 8.0 and want to find out how can I go in and change my network setup and external IP setup. At the moment system running but I can not connect to the internet. But my lan card shows that I am on the network. I also get some advice that I should check the $Socks but how do I... (1 Reply)
Discussion started by: Cdrive
1 Replies
2. UNIX for Dummies Questions & Answers
Im on XP now but when im on linux how do I connect to the internet?
I don't think AOL works with it but are there any free programs that I can use with it? (8 Replies)
Discussion started by: NoPepsiForYou
8 Replies
3. UNIX for Dummies Questions & Answers
Hi all,
Is it possible (as I only have dial-up) to utilise my existing WinXP PC as a gateway to the internet for my 2nd PC (RH 8.0)?? .So connect with XP and have RH use a network connection (I guess) through the XP box and to the internet.
If so, could I please have some links thrown my... (1 Reply)
Discussion started by: Cameron
1 Replies
4. UNIX for Dummies Questions & Answers
I am using solaris 10 with pentium 3. I have two network cards but none of them come up when i run <ifconfig -a> in command line. The two cards I have are : Linksys LNE 100TX and Netgear FA311. Does solaris 10 support these NICs or do I have to dowload the drivers for them.
If so, can anyone... (1 Reply)
Discussion started by: fidjouss
1 Replies
5. Linux
Hi,
I can ping www.yahoo.com (then domain name server is OK) but I can not navigate by Motzila to www.yahoo.com or any other Web Site.
What can be the problem ? Mozila is configured in preference /advance to go automaticaly on WEB.
We are under RED HAT AS3.
What should I check ?
Many thanks... (1 Reply)
Discussion started by: big123456
1 Replies
6. UNIX for Dummies Questions & Answers
I have just installed Linux and everything looks great, but how do I get my browser (Mozilla) to connect to my internet service provider?
I have a cable connection to Bigpond in Australia, if that means anything - the ISP will not provide support for Linux.
Your help would be greatly... (2 Replies)
Discussion started by: openhead
2 Replies
7. SuSE
I have been hunting about the internet for a while not trying to find a way to connect to the internet via WiFi with Fedora Core 5 with no luck however.
I have a Netgear ADSL2+ DGB111G Router and a matching USB WiFi card (came packaged together). I have it up and running on WinXP Home SP2 fine,... (1 Reply)
Discussion started by: crmpicco
1 Replies
8. UNIX for Dummies Questions & Answers
This seems to be a common problem. I just installed Solaris 10 and do not have an internet connection. I am not that savy with Unix/Linux, although I have been using Linux in the past, and have never had any sort of problem detecting my internet connection. I have tried some things, but did not... (9 Replies)
Discussion started by: eric cartman
9 Replies
9. UNIX for Dummies Questions & Answers
I am trying to connect a Solaris 10 PC to the internet via a Linksys router and a cable modem. I have tried following suggestions in one of the posts here for manual setup but so far no luck.
Does the Solaris 10 install for x86 automatically pick up the internet connection?
Dave :>) (4 Replies)
Discussion started by: dohling
4 Replies
10. SCO
Hi, I have a router, 192.168.1.1, and an internet router, 10.0.0.138. I have connected the server to the 1st router and assigned it a IP address of 192.168.1.1. I can ping both routers successfully but I have no access to internet. Any suggestions? sco5.0.7 (11 Replies)
Discussion started by: juan.navarrete
11 Replies
route(8c) route(8c)
Name
route - manually manipulate the routing tables
Syntax
/etc/route [ -f ] [ -n ] command args ]
Description
The program is used to manipulate the network routing tables manually. However, normally it is not needed, as the system routing table
management daemon, should tend to this task.
The program accepts two commands: add, to add a route and delete, to delete a route.
All commands have the following syntax:
/etc/route command [ net | host ] destination gateway [ metric ]
In this syntax, destination is a host or network for which the route is to, gateway is the gateway to which packets should be addressed,
and metric is an optional count indicating the number of hops to the destination. The metric is required for add commands. It must be
zero if the destination is on a directly-attached network, and nonzero if the route utilizes one or more gateways.
When adding a route with metric 0, the gateway given is the address of this host on the common network, indicating the interface to be used
for transmission. Routes to a particular host are distinguished from routes to a network by interpreting the Internet address associated
with destination. The optional keywords net and host force the destination to be interpreted as a network or host, respectively. If the
destination has a local address part of INADDR_ANY, then the route is assumed to be to a network. Otherwise, it is presumed to be a route
to a host. If the route is to a destination connected via a gateway, the metric should be greater than 0. All symbolic names specified
for a destination or gateway are looked up first as a host name using If this lookup fails, is then used to interpret the name as that of a
network.
The command uses a raw socket and the SIOCADDRT and SIOCDELRT ioctls to do its work. As such, only the superuser can modify the routing
tables.
Options
-f Flushes the routing tables of all gateway entries. If is used with one of the commands described above, the tables are flushed prior
to the command's application.
-n Prevents attempts to print host and network names symbolically when reporting actions.
Restrictions
The change operation is not implemented. Therefore, you should first add the new route, and then delete the old one.
Diagnostics
add [host | network] %s: gateway %s flags %x"
The specified route is being added to the tables. The values printed are from the routing table entry supplied in the ioctl call. If the
gateway address used was not the primary address of the gateway (the first one returned by the gateway address is printed numerically as
well as symbolically.
delete [ host | network] %s: gateway %s flags %x
The specified route is being deleted from the tables. The values printed are from the routing table entry supplied in the ioctl call. If
the gateway address used was not the primary address of the gateway (the first one returned by the gateway address is printed numerically
as well as symbolically.
%s %s done
When the flag is specified, each routing table entry that is deleted is indicated with a message of this form.
Network is unreachable
An attempt to add a route failed because the gateway listed was not on a directly-connected network. The next-hop gateway must be given.
not in table
A delete operation was attempted for an entry which was not present in the tables.
routing table overflow
An add operation was attempted, but the system was low on resources and was unable to allocate memory to create the new entry.
See Also
intro(4n), routed(8c)
route(8c)