Sponsored Content
Special Forums IP Networking radvd + ipv6 problems in Linux Post 23800 by wag on Sunday 30th of June 2002 03:30:19 PM
Old 06-30-2002
Go to the usr/src/linux-2.4.5 and run make menuconfig
setup IPv6[*] and all ather you need then exit with save
and make install. Sorry for my English Smilie
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Linux problems

Hi I'm using linux slackware 8.0 with the 2.2.19 kernel I have some problems.. First problem: I cannot get kernel 2.4.* to work.. it hangs when I boot and displays someting like: configuring 100mbps tbase 100x full duplex what can cause this? and what can I do about it? Second... (4 Replies)
Discussion started by: Maestin
4 Replies

2. Linux

ipv6 on a linux box

how to enable an ipv6 address on a linux pc? thanks in advance (3 Replies)
Discussion started by: sunittaneja
3 Replies

3. SuSE

Linux and IPv6

Hi gurus, In a few month, we must enable IPv6 on our Linux Server! Should we reinstall the Linux machine to enable IPv6 or could we just make some change in configuration's files? Could Linux run simultaneous IPv4 and IPv6? Thanks in advance for our help our ideas? Best regards, nm (3 Replies)
Discussion started by: hiddenshadow
3 Replies

4. IP Networking

Radvd wlan problems

Hi all, I am trying to get radvd to broadcast router advertisements on a wireless interface (wlan0). The wireless interface is running an ad-hoc wireless network. However, for some reason, radvd will say that wlan0 not running and refuse to start. The only way I can get radvd to broadcast... (0 Replies)
Discussion started by: abxccd
0 Replies

5. IP Networking

radvd isatap clients can not connect with each other?

My radvd works well.The isatap clients could connected IPV6 network,but,they can not connect with each other?why? my radvd conf like this: interface is0 { AdvSendAdvert on; UnicastOnly on; AdvHomeAgentFlag off; prefix 2001:250:5405:1::/64 { AdvOnLink on; AdvAutonomous on; ... (0 Replies)
Discussion started by: LiuKai
0 Replies

6. Linux

Help Me: How to set ARP stale time interval on linux platform for Ipv6 interface

Hi, Can any one please help me increase the arp stale time of an ipv6 interface on linux platform ? I have tried increasing the variable gc_stale_time but that doesnt work. Thanks (2 Replies)
Discussion started by: dkothapa
2 Replies

7. IP Networking

Linux Bridging, Wireless AP, IPv6 multicast and autoconfiguration.

Well I cannot be too certain of the setup, since it's a stock firmware, but I have a cheap Belkin wireless-n router and wanted to get some ideas of what may be going on while I've a few moments to ramble on about my problems... I requested the GPL source so I've just been pondering while waiting to... (0 Replies)
Discussion started by: neutronscott
0 Replies

8. UNIX for Dummies Questions & Answers

Assigning ipv6 to bonding interface - getting old as well as changed ipv6 in ifconfig output

Hi, I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies

9. IP Networking

IPv6 Problems

I am trying to setup an IPv6 network. I modified the interfaces file: /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback iface etho0 inet static address 2620:7:a000::1 netmask 64 gateway ::ffff:c0a8:101 ... (0 Replies)
Discussion started by: Meow613
0 Replies
DH_AUTO_INSTALL(1)						     Debhelper							DH_AUTO_INSTALL(1)

NAME
dh_auto_install - automatically runs make install or similar SYNOPSIS
dh_auto_install [buildsystemoptions] [debhelperoptions] [--params] DESCRIPTION
dh_auto_install is a debhelper program that tries to automatically install built files. It does so by running the appropriate command for the build system it detects the package uses. For example, if there's a Makefile and it contains a install target, then this is done by running make (or MAKE, if the environment variable is set). If there is a setup.py or Build.PL, it is used. Note that the Ant build system does not support installation, so dh_auto_install will not install files built using Ant. Unless --destdir option is specified, the files are installed into debian/package/ if there is only one binary package. In the multiple binary package case, the files are instead installed into debian/tmp/, and should be moved from there to the appropriate package build directory using dh_install(1). DESTDIR is used to tell make where to install the files. If the Makefile was generated by MakeMaker from a Makefile.PL, it will automatically set PREFIX=/usr too, since such Makefiles need that. This is intended to work for about 90% of packages. If it doesn't work, or tries to use the wrong install target, you're encouraged to skip using dh_auto_install at all, and just run make install manually. OPTIONS
See "BUILD SYSTEM OPTIONS" in debhelper(7) for a list of common build system selection and control options. --destdir=directory Install files into the specified directory. If this option is not specified, destination directory is determined automatically as described in the "DESCRIPTION" section. -- params Pass params to the program that is run, after the parameters that dh_auto_install usually passes. SEE ALSO
debhelper(7) This program is a part of debhelper. AUTHOR
Joey Hess <joeyh@debian.org> 11.1.6ubuntu2 2018-05-10 DH_AUTO_INSTALL(1)
All times are GMT -4. The time now is 01:28 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy