Sponsored Content
Full Discussion: ethernet card for Solaris
Special Forums Hardware Filesystems, Disks and Memory ethernet card for Solaris Post 23728 by auswipe on Thursday 27th of June 2002 09:33:50 PM
Old 06-27-2002
Quote:
Originally posted by RTM
There is no file to change from half to full duplex. You have to use the ndd commands (see the man page).

You can search this site for ndd and find more questions (with answers) on this subject. If you need further help, post back.
Will ifconfig allow the duplex to be changed under Solaris? I could've swore that it did.
 

10 More Discussions You Might Find Interesting

1. IP Networking

Solaris 9 Ethernet Card Problems

I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem? I am using the command: ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies

2. IP Networking

RedHat and Ethernet card no like each other

I have searched this forum for solution and have drawn a blank... so I come to you for help :) I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies

3. UNIX for Dummies Questions & Answers

Ethernet card problem...

I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies

4. AIX

Add PCI ethernet card?

Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies

5. SCO

Issue with a ethernet card

Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message: Fsstat:/dev/boot mounted Mounted /stand filesystem System auditing is not enabled. Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0) Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies

6. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies

7. AIX

Utilization of Ethernet Card

Hi, is it possible to find out network utilization of etherenet card in %? Regards, Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies

8. Solaris

solaris ethernet card and mounting usb drives

I had installed soalris 10 on my dell vostro 1400.It had installed succefully. If i type ifconfig -a it is showing only my loop back adpater. So how to tell me how to mount my usb drive and how to configure my lan ethernet card,My lan ethernet card is Broadcom. Tell me step... (1 Reply)
Discussion started by: testerindia25
1 Replies

9. Solaris

SUN GIGABIT ETHERNET CARD

Hi, we have SUN Gigabit ethernet cards at the server, both have 2 lines connected but hiw can I found out which cable is on which port before I configure it: the cards has 4 ports , from right to left the cables are connected at the first right then 2 empty then the last at the left side. ... (1 Reply)
Discussion started by: manni2
1 Replies

10. Solaris

Problem with my Ethernet Card

Hi Gurus of Solaris. I have a problem yesterday when I was installing solaris in a x86 equipement I attached some log that I capture when I try to resolve the problem Any guru that can help please. Any command or procedure that I can run, please advice me Regards Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
TXP(4)							   BSD Kernel Interfaces Manual 						    TXP(4)

NAME
txp -- 3Com 3XP Typhoon/Sidewinder (3CR990) Ethernet interface SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file: device txp Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_txp_load="YES" DESCRIPTION
The txp interface provides access to the 10Mb/s and 100Mb/s Ethernet networks via the 3Com Typhoon/Sidewinder chipset. Basic Ethernet functions are provided as well as support for vlan(4) tag removal and insertion assistance, receive ip(4), tcp(4), and udp(4) checksum offloading, and transmit ip(4) checksum offloading. There is currently no support for transmit tcp(4) or udp(4) checksum offload- ing, tcp(4) segmentation, nor ipsec(4) acceleration. When a txp interface is brought up, by default, it will attempt to auto-negotiate the link speed and duplex mode. The speeds, in order of attempt, are: 100Mb/s Full Duplex, 100Mb/s Half Duplex, 10 Mb/s Full Duplex, and 10 Mb/s Half Duplex. The txp supports several media types, which are selected via the ifconfig(8) command. The supported media types are: media autoselect Attempt to autoselect the media type (default) media 100baseTX mediaopt full-duplex Use 100baseTX, full duplex media 100baseTX [mediaopt half-duplex] Use 100baseTX, half duplex media 10baseT mediaopt full-duplex Use 10baseT, full duplex media 10baseT [mediaopt half-duplex] Use 10baseT, half duplex HARDWARE
The txp driver supports the following cards: o 3Com 3CR990-TX-95 o 3Com 3CR990-TX-97 o 3Com 3cR990B-TXM o 3Com 3CR990SVR95 o 3Com 3CR990SVR97 o 3Com 3cR990B-SRV SEE ALSO
altq(4), arp(4), inet(4), intro(4), ip(4), miibus(4), tcp(4), udp(4), vlan(4), ifconfig(8) HISTORY
The txp driver first appeared in OpenBSD 2.9. BSD
January 26, 2012 BSD
All times are GMT -4. The time now is 01:34 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy