|
|
Sponsored Content
Special Forums
Hardware
Filesystems, Disks and Memory
ethernet card for Solaris
Post 23697 by auswipe on Thursday 27th of June 2002 01:17:39 PM
06-27-2002
|
|
10 More Discussions You Might Find Interesting
1. IP Networking
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies
2. IP Networking
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies
3. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
4. AIX
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies
5. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
8. Solaris
I had installed soalris 10 on my dell vostro 1400.It had installed succefully.
If i type ifconfig -a it is showing only my loop back adpater.
So how to tell me how to mount my usb drive and how to configure
my lan ethernet card,My lan ethernet card is Broadcom.
Tell me step... (1 Reply)
Discussion started by: testerindia25
1 Replies
9. Solaris
Hi,
we have SUN Gigabit ethernet cards at the server, both have 2 lines connected but hiw can I found out which cable is on which port before I configure it: the cards has 4 ports , from right to left the cables are connected at the first right then 2 empty then the last at the left side.
... (1 Reply)
Discussion started by: manni2
1 Replies
10. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
LEARN ABOUT CENTOS
grub-file
GRUB-FILE(1) User Commands GRUB-FILE(1) NAME
grub-file - check file type SYNOPSIS
file OPTIONS FILE DESCRIPTION
Check if FILE is of specified type. --is-i386-xen-pae-domu Check if FILE can be booted as i386 PAE Xen unprivileged guest kernel --is-x86_64-xen-domu Check if FILE can be booted as x86_64 Xen unprivileged guest kernel --is-x86-xen-dom0 Check if FILE can be used as Xen x86 privileged guest kernel --is-x86-multiboot Check if FILE can be used as x86 multiboot kernel --is-x86-multiboot2 Check if FILE can be used as x86 multiboot2 kernel --is-arm-linux Check if FILE is ARM Linux --is-arm64-linux Check if FILE is ARM64 Linux --is-ia64-linux Check if FILE is IA64 Linux --is-mips-linux Check if FILE is MIPS Linux --is-mipsel-linux Check if FILE is MIPSEL Linux --is-sparc64-linux Check if FILE is SPARC64 Linux --is-powerpc-linux Check if FILE is POWERPC Linux --is-x86-linux Check if FILE is x86 Linux --is-x86-linux32 Check if FILE is x86 Linux supporting 32-bit protocol --is-x86-kfreebsd Check if FILE is x86 kFreeBSD --is-i386-kfreebsd Check if FILE is i386 kFreeBSD --is-x86_64-kfreebsd Check if FILE is x86_64 kFreeBSD --is-x86-knetbsd Check if FILE is x86 kNetBSD --is-i386-knetbsd Check if FILE is i386 kNetBSD --is-x86_64-knetbsd Check if FILE is x86_64 kNetBSD --is-i386-efi Check if FILE is i386 EFI file --is-x86_64-efi Check if FILE is x86_64 EFI file --is-ia64-efi Check if FILE is IA64 EFI file --is-arm64-efi Check if FILE is ARM64 EFI file --is-arm-efi Check if FILE is ARM EFI file --is-hibernated-hiberfil Check if FILE is hiberfil.sys in hibernated state --is-x86_64-xnu Check if FILE is x86_64 XNU (Mac OS X kernel) --is-i386-xnu Check if FILE is i386 XNU (Mac OS X kernel) --is-xnu-hibr Check if FILE is XNU (Mac OS X kernel) hibernated image --is-x86-bios-bootsector Check if FILE is BIOS bootsector -h, --help Display this help and exit. -u, --usage Display the usage of this command and exit. SEE ALSO
The full documentation for grub-file is maintained as a Texinfo manual. If the info and grub-file programs are properly installed at your site, the command info grub-file should give you access to the complete manual. grub-file (GRUB) 2.02-2ubuntu8.3 July 2018 GRUB-FILE(1)