Sponsored Content
Special Forums Hardware Filesystems, Disks and Memory terminal/port (serial) lock up mystery! SCO 5.0 Post 22473 by DjWolfman on Tuesday 4th of June 2002 02:05:42 PM
Old 06-04-2002
Have you tried to replace the digi card in the server?
it also could be the card itself that is running amuck in your server give this a try



Smilie
 

10 More Discussions You Might Find Interesting

1. Programming

Telling apart serial from // port

I'm writing a journal_write() function and I want it to: - be a possible drop in replacement for write() - write entries to the journal ;-) Could be a regular file (journal.txt), a serial printer or a // printer. - handle printer status if needed. fstat() tells weather or not we're dealing with... (2 Replies)
Discussion started by: starless
2 Replies

2. Solaris

serial port signal

hi i am using solaris 9 on sparc . i was wondering if there was a command to control my serial interface , as to send a signal periodically every interval of time to the input of a 555 timer . thanks for your help .... (0 Replies)
Discussion started by: ppass
0 Replies

3. UNIX for Dummies Questions & Answers

How to read lock terminal values in solaris

Hi all I am using sun solaris 5.8. I wanna know where the value stored if we lock/unlock the terminal and how i can read and use it to my script. I am helpless . So plzzzzzz... (0 Replies)
Discussion started by: pankajarora_12
0 Replies

4. Linux

urgent......Serial port

I think my serial port(on board) is not working ...... because when I am running same code on two machines its working good....but when my system comes into picture ....it doesnt show any output comming from serial port.......... can anybody tell me how to configure my serial port.........or to... (16 Replies)
Discussion started by: arunchaudhary19
16 Replies

5. SCO

Serial port configuration

Hi I have just re-installed Compaq ML350 G2 Server with Unix SCO 5.0.5 and informix DBMS . on this server we have 2 serial ports , unfortunately its not working. Can anyone help me to check the serial ports working or not OR guide me to reconfigure it. I have attached a device with... (1 Reply)
Discussion started by: munirh
1 Replies

6. Solaris

Not able to lock the port

Hi, I am working with Sun-Solaris 9 and in our application I need to connect the UPS with Serial port,after that I need to monitor it..but before stating communication,It should lock that port,To check it,first i am trying to make sure the lock directory exists and I am able to find it(/var/lock)... (0 Replies)
Discussion started by: smartgupta
0 Replies

7. Shell Programming and Scripting

Need help with serial port

Hi, I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Discussion started by: charlie.arya
0 Replies

8. Solaris

How to enable Serial port on ILOM, when Network Port is enabled in parallel

Hi Everyone, In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies

9. Web Development

Setup Serial Port

I need to set a serial port to 9600 7E1. How do I accomplish this? I've tried every combination, with no luck. (6 Replies)
Discussion started by: Meow613
6 Replies

10. Solaris

Cabling and adapters to communicate to service processor serial port from Windows PC with USB port.

Hello, I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build. The first part is what confuses me -the cabling. I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
DAIC(4) 						   BSD Kernel Interfaces Manual 						   DAIC(4)

NAME
daic -- isdn4bsd driver for EICON.Diehl active ISDN cards SYNOPSIS
daic0 at isa? iomem 0xd8000 irq 10 DESCRIPTION
The daic driver supports the old Diehl active cards: S, SX, SXn, SCOM and QUADRO. For a QUADRO card, the driver will detect the board type and use all four ports, each attached as a controller of its own to the isdn4bsd system, which can be listed using the daicctl utility. The daic driver interfaces the ISDN card to the ISDN4BSD kernel subsystem. All lower layer ISDN control is handled by the card. This should allow you to run any national ISDN protocol delivered by EICON.Diehl for your card, but the driver has only been tested with the DSS1 proto- col and some parts of the cards interface are ISDN protocol dependent. The daic driver is written to conform to the software interface documented by Diehl in their ISDN-Karten Benutzerhandbuch from 1992. MICROCODE DOWNLOAD
Every active card needs its own operating software before it can work. You have to download this to the card before using it with isdn4bsd. Use the daicctl utility to do this, i.e. call daicctl -d te_etsi.sx 1 to download the file te_etsi.sx to controller number 1. Use daicctl -l to list all available controllers (and ports). You have to select the correct ISDN protocol file for your ISDN interface, see the Diehl docu- mentation for details. The cards bootstrap process involves another file, which is independent of the card type you use and the protocol you run. It is called download.bin in current versions of the Diehl software distribution and has to be copied to the kernel compile directory under dev/microcode/daic and converted into a header file used when compiling the kernel by running make in that directory. Your kernel compile will fail and remind you of this if you forget to do this. Due to copyright restrictions we cannot distribute the driver with this file inte- grated. But if you own a card, you do have the file (or can get it from the Diehl web server). SEE ALSO
daicctl(1) BUGS
The driver is not yet finished. BSD
January 30, 1998 BSD
All times are GMT -4. The time now is 03:09 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy