Sponsored Content
Special Forums Hardware Filesystems, Disks and Memory terminal/port (serial) lock up mystery! SCO 5.0 Post 22473 by DjWolfman on Tuesday 4th of June 2002 02:05:42 PM
Old 06-04-2002
Have you tried to replace the digi card in the server?
it also could be the card itself that is running amuck in your server give this a try



Smilie
 

10 More Discussions You Might Find Interesting

1. Programming

Telling apart serial from // port

I'm writing a journal_write() function and I want it to: - be a possible drop in replacement for write() - write entries to the journal ;-) Could be a regular file (journal.txt), a serial printer or a // printer. - handle printer status if needed. fstat() tells weather or not we're dealing with... (2 Replies)
Discussion started by: starless
2 Replies

2. Solaris

serial port signal

hi i am using solaris 9 on sparc . i was wondering if there was a command to control my serial interface , as to send a signal periodically every interval of time to the input of a 555 timer . thanks for your help .... (0 Replies)
Discussion started by: ppass
0 Replies

3. UNIX for Dummies Questions & Answers

How to read lock terminal values in solaris

Hi all I am using sun solaris 5.8. I wanna know where the value stored if we lock/unlock the terminal and how i can read and use it to my script. I am helpless . So plzzzzzz... (0 Replies)
Discussion started by: pankajarora_12
0 Replies

4. Linux

urgent......Serial port

I think my serial port(on board) is not working ...... because when I am running same code on two machines its working good....but when my system comes into picture ....it doesnt show any output comming from serial port.......... can anybody tell me how to configure my serial port.........or to... (16 Replies)
Discussion started by: arunchaudhary19
16 Replies

5. SCO

Serial port configuration

Hi I have just re-installed Compaq ML350 G2 Server with Unix SCO 5.0.5 and informix DBMS . on this server we have 2 serial ports , unfortunately its not working. Can anyone help me to check the serial ports working or not OR guide me to reconfigure it. I have attached a device with... (1 Reply)
Discussion started by: munirh
1 Replies

6. Solaris

Not able to lock the port

Hi, I am working with Sun-Solaris 9 and in our application I need to connect the UPS with Serial port,after that I need to monitor it..but before stating communication,It should lock that port,To check it,first i am trying to make sure the lock directory exists and I am able to find it(/var/lock)... (0 Replies)
Discussion started by: smartgupta
0 Replies

7. Shell Programming and Scripting

Need help with serial port

Hi, I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Discussion started by: charlie.arya
0 Replies

8. Solaris

How to enable Serial port on ILOM, when Network Port is enabled in parallel

Hi Everyone, In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies

9. Web Development

Setup Serial Port

I need to set a serial port to 9600 7E1. How do I accomplish this? I've tried every combination, with no luck. (6 Replies)
Discussion started by: Meow613
6 Replies

10. Solaris

Cabling and adapters to communicate to service processor serial port from Windows PC with USB port.

Hello, I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build. The first part is what confuses me -the cabling. I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
sredird(8)							      sredird								sredird(8)

NAME
sredird - RFC 2217 serial port server SYNOPSIS
sredird [-i] log-level serial-device lock-file [poll-interval] DESCRIPTION
This manual page documents briefly the sredird, program. This program when run through inetd will use the RFC 2217 extensions to TELNET to implement serial commands over the TCP connection and interface to a specified serial port. OPTIONS
An optional first parameter is '-i' to enable compatability with Cisco IOS. The first mandatory parameter is the log level for use in syslog. The next mandatory parameter is the device node for the serial device, it must be a fully qualified path. The final mandatory parameter is the file name for the lock file to be used to prevent multiple instances of sredird from talking to the serial port at the same time, or to allow sharing a port between modem and sredird. EXAMPLE
Here is a configuration line for running it from inetd: sredir stream tcp nowait root /usr/sbin/tcpd /usr/sbin/sredird 5 /dev/modem /var/lock/LCK..modem AUTHOR
This man page was written by Russell Coker <russell@coker.com.au>. May be freely used and distributed without restriction under the terms of the GPL. The sredird program was written by Denis Sbragion <d.sbragion@infotecna.it> and Jeffrey Altman <jaltman@columbia.edu>. Russell Coker <;russell@coker.com.au> 2.2.0 sredird(8)
All times are GMT -4. The time now is 11:14 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy