11-10-2000
There are many kinds of swap space. PxT accurately decribes disk space swap. Mr JuniorUnix accurately describes file space swap. Most people consider file space swap to be much less efficient and slower than disk space swap. I would recommend some research into the subject and make sure that you will be happy with file space swap vs. disk swap. Just to let you know, we never use file swap and always use raw disk swap. There is a considerable difference in performance between the two, as I recall.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello,
I would like to know if there is any difference between the pageing space and the swap space.
Thank you in advance. (1 Reply)
Discussion started by: VeroL
1 Replies
2. UNIX for Dummies Questions & Answers
I checked the server and issued various command to investigated. but from teh output of swap -s and swap -l,
i received the following
swap -l
swapfile dev swaplo blocks free
/dev/vx/dsk/swapvol 197,7 16 4194800 4127696
/dev/vx/dsk/swap2 197,8 16 12582896... (3 Replies)
Discussion started by: TRUEST
3 Replies
3. AIX
how do you get the paging space reduced without rebooting the machine ? the os is aix (2 Replies)
Discussion started by: aaronh
2 Replies
4. UNIX for Dummies Questions & Answers
Plz I need to know how much swap mem free and used i have.
I'm using Compaq Tru64 UNIX V5.1A (rev 1885)
Thanx (1 Reply)
Discussion started by: Lestat
1 Replies
5. Linux
Hi,
I want to know how can i free the swap space if it is completely full,
0 mb remaining, (1 Reply)
Discussion started by: manoj.solaris
1 Replies
6. Solaris
Could someone please explain how you know how much swap space you have on your system. See below:
# swap -s
total: 8225048k bytes allocated + 4863488k reserved = 13088536k used, 4008032k available
# swap -l
swapfile dev swaplo blocks free
/dev/dsk/c3t0d0s1 32,25 16... (2 Replies)
Discussion started by: jamba1
2 Replies
7. Linux
Hi,
i have done a blunder here, i increased the swap space on Xen5.6 server machine using below steps :-
1056 dd if=/dev/zero of=/root/myswapfile bs=1M count=1024
1057 ls -l /root/myswapfile
1058 chmod 600 /root/myswapfile
1059 mkswap /root/myswapfile
1060 swapon /root/myswapfile
... (1 Reply)
Discussion started by: apm
1 Replies
8. Solaris
Dear All,
I have a swap space of 16G available in Sol 10. I have allocated it as a seperate file system. But when the RAM Is full used , the system gets rebooted and the swap is not being used,.
Any reasons for this.
Rgds
Rj (5 Replies)
Discussion started by: jegaraman
5 Replies
9. Red Hat
CENT OS 5.8 server running with a huge java application which uses up all my ram (4GB) and requires excess of atleast 2GB.But the swap is not getting used up((8GB) of swap space left unused) leading a wierd error and stopping application to stop working.
Any one here dealt with the same kind of... (2 Replies)
Discussion started by: shiek.kaleem
2 Replies
10. Red Hat
I've to install Oracle binaries (I'm oracle DBA) and for that I've extend swap space in my home computer. My situation is like this.
# parted -s /dev/sda print free
Model: ATA VBOX HARDDISK (scsi)
Disk /dev/sda: 38.7GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos
... (1 Reply)
Discussion started by: Mukul Sharma
1 Replies
LEARN ABOUT OSF1
disklabel
disklabel(4) Kernel Interfaces Manual disklabel(4)
NAME
disklabel - Disk pack label
SYNOPSIS
#include <sys/disklabel.h>
DESCRIPTION
Each disk or disk pack on a system may contain a disk label which provides detailed information about the geometry of the disk and the par-
titions into which the disk is divided. It should be initialized when the disk is formatted, and may be changed later with the disklabel
program. This information is used by the system disk driver and by the bootstrap program to determine how to program the drive and where
to find the file systems on the disk partitions. Additional information is used by the file system in order to use the disk most effi-
ciently and to locate important file system information. The description of each partition contains an identifier for the partition type
(standard file system, swap area, etc.). The file system updates the in-core copy of the label if it contains incomplete information about
the file system.
The label is located in sector number LABELSECTOR of the drive, usually sector 0 (zero) where it may be found without any information about
the disk geometry. It is at an offset LABELOFFSET from the beginning of the sector, to allow room for the initial bootstrap. The disk
sector containing the label is normally made read-only so that it is not accidentally overwritten by pack-to-pack copies or swap opera-
tions; the DIOCWLABEL ioctl, which is done as needed by the disklabel program, allows modification of the label sector.
A copy of the in-core label for a disk can be obtained with the DIOCGDINFO ioctl; this works with a file descriptor for a block or charac-
ter (raw) device for any partition of the disk. The in-core copy of the label is set by the DIOCSDINFO ioctl. The offset of a partition
cannot generally be changed, nor made smaller while it is open. One exception is that any change is allowed if no label was found on the
disk, and the driver was able to construct only a skeletal label without partition information. Finally, the DIOCWDINFO ioctl operation
sets the in-core label and then updates the on-disk label; there must be an existing label on the disk for this operation to succeed.
Thus, the initial label for a disk or disk pack must be installed by writing to the raw disk. All of these operations are normally done
using the disklabel program.
RELATED INFORMATION
Files: disktab(4)
Commands: disklabel(8) delim off
disklabel(4)