04-27-2002
Cool, glad it worked, and thanks for posting back
10 More Discussions You Might Find Interesting
1. IP Networking
If the cable modem that the cable company is using doesn't support unix is there a way around that . Are there drivers I can get online or is there a way to configure redhat lenix (that's what I will be using) to work with the cable modem. Or is there a way to buy a third party cable modem that... (3 Replies)
Discussion started by: gparsons70
3 Replies
2. UNIX for Dummies Questions & Answers
I recently installed Caldera 2.4 (successfully:p ), but I cannot seem to get my cable modem up and running! My ISP is AT&T and I'm using @home. I've tried using DHCP and that didn't work either. I briefly read the cable modem HOWTO, but the lsmod didn't list my network card (3COM). What do I do now? (4 Replies)
Discussion started by: zorro
4 Replies
3. UNIX for Dummies Questions & Answers
Caldera eDesktop 2.4 - Cable Modem
my NIC card has been detected, but funny scenario:
#dmesg
eth0: RealTek rtl8139 Fast Ethernet at 0x2400, IRQ 0, 00:50:ba:43:a0:ef
/*I noticed that it detected the correct module (rtl8139) but I'm using D-Link and not RealTek, which uses the same module.... (1 Reply)
Discussion started by: zorro
1 Replies
4. UNIX for Dummies Questions & Answers
Is anyone using a cable modem with unix and if so does your cable co. support unix or did you get that going on your own and how.
Thank you for all your help. (5 Replies)
Discussion started by: gparsons70
5 Replies
5. UNIX for Dummies Questions & Answers
hi , i have sparc machine , i want to connect my le0 (ethernet interface) directly to cable modem ,
i have created a file resolv.conf,hosts, dhcp.le0,defaultrouter,nisswitch,hostname.le0. i dont know my cable companies <domain name> and <name server assigned to me> , also they even dont know how... (5 Replies)
Discussion started by: raju
5 Replies
6. UNIX for Dummies Questions & Answers
Ok I am new to this and wondering if there is any way of connecting a cable modem to an SGI that is running IRIX 6.5 and how to do it... (1 Reply)
Discussion started by: Acidjack
1 Replies
7. BSD
hi
I want to setup my cable modem under OpenBSD. I did not configure my network while installing the system.
When I type, I get
# ifconfig -a
lo0 : ....
...
...
rl0 : ....
...
...
vr0 : ...
...
...
I have two network cards (the machine will be a router).
I created... (1 Reply)
Discussion started by: fnoyan
1 Replies
8. Solaris
Hi all,
Is there any difference between a null modem cable or a modem cable ?
i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup.
please correct if i am wrong,
thks (2 Replies)
Discussion started by: waterbear
2 Replies
9. Solaris
I have a dual boot system with XP being the primary for now and Solaris 10 being the Secondary. I have a cable modem and wish to configure the same to be used with Solaris so that I can browse the Internet and such.
I have connected my x86 machine with a Netgear Router and that in turn is... (7 Replies)
Discussion started by: tubbyrana
7 Replies
10. OS X (Apple)
Hi.
I have a very strange problem, so strange I don't even know which sub-forum to post it to.
Last week, my cable modem broke, so I took it back and got a new one.
The new one doesn't work with my old router so, for now, I have to connect the modem directly to my Mac with an ethernet... (14 Replies)
Discussion started by: Scott
14 Replies
KITSEND(1) General Commands Manual KITSEND(1)
NAME
kitpost - posts distribution kits
SYNOPSIS
kitpost [ -hrV ] [ -H file ] [ -D desc ] [ -m dest1,dest2 ] [ kits ] [ newsgroups ]
DESCRIPTION
Kitpost posts distribution kits made by makedist to some (source) newsgroups specified on the command line. If you do not specify any kit
list, then all the kits are sent. Otherwise, only the specified kits will be (re)sent.
A kit list may include ranges, 1-10 specifying kits 1 through 10, and 5- meaning kits 5 up to the last one. You may also specify kit num-
bers by separating them with commas or spaces, and even mix with ranges, such as: 1 3 5-7 9.
Kitpost ensures correct References: lines are inserted in your postings so that all parts but the first point to the root article. Threaded
newsreaders and end-users traditionally appreciate that.
OPTIONS
The following options are recognized by kitpost:
-h Print help message and exit.
-m dest1,destn
Sends kits by e-mail to the specified recipients. This option may be used in conjunction with newsgroup posting. It is mainly
intended for sites where direct posting to a moderated newsgroup is not allowed by inews. You may thus send your kits to the
newsgroup moderator in a form that will ease the whole posting process.
-r Signals a repost.
-D description
Specify a description string that will be added to the subject line. Usually a brief sentence (less than, say, 40 characters).
-H file Specify a file to be used as header introduction in the first part of your posting. Usually the root README file.
-V Print version number and exit.
BUGS
Article cross-referencing is properly set-up only when the whole package is (re)posted in one batch.
It is not currently possible to set-up the article headers manually or better, interactively.
AUTHOR
Raphael Manfredi <ram@hptnos02.grenoble.hp.com>
SEE ALSO
makedist(1), kitsend(1).
ram KITSEND(1)