04-23-2002
Ethernet
We are trying to Establish Network using Linux.Now we are facing the problem in configring Ethernet.In out network we are giving eth0 in server and activating it at the boot time,so it is activating as it is but when we define the Ethernet of node on server and allowing it to activate at boot time then it is not activating.so i want to know that what is the reason behind this and what should i have to do to overcome this problem.When i give the ethernet on nodes seprately then also Linux displays it failed at boot time.Plaese Help Me
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I am using Red Hat 7.1 . I have installed one Server and trying to make network installing workstations on other system of a network. The Ethernet of the server has been mounted and working properly. I am getting problem installing /mounting the Ethernet of the workstations .I have tryed this by... (1 Reply)
Discussion started by: at_renai2001
1 Replies
2. Cybersecurity
I suspect that someone is using a sniffer on my Ethernet connection,
OS X 10.3.9, DSL,
ok, I'm in terminal using the "ifconfig" command >
flags=8049<UP,LOOPBACK,RUNNING,MULTICAST>mtu 16384
right, it's not in "promiscuous mode", but i think it's Trojaned, can anyone point me in the... (1 Reply)
Discussion started by: su"do"er
1 Replies
3. UNIX for Advanced & Expert Users
I understand that one should setup virtual ethernet adapters in the lpars which is the best way for various lpars to communicate with each other - Does anyone have info on this or can point me to a doc that explains how to set this up? (1 Reply)
Discussion started by: capeme
1 Replies
4. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
5. Solaris
Boot device: /pci@8,600000/SUNW,qlc@4/fp@0,0/disk@w500000e0103c3391,0:a File and args:
SunOS Release 5.8 Version Generic_108528-29 64-bit
Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved.
ifconfig: plumb: qfe2: Bad file number
configuring IPv4 interfaces: eri0.
moving addresses... (1 Reply)
Discussion started by: fredginting
1 Replies
6. AIX
Hello everyone
I have a problem with one server, has Aix 5.3 in the errpt has this message
IDENTIFIER TIMESTAMP T C RESOURCE_NAME DESCRIPTION
F3931284 0105133009 I H ent0 ETHERNET NETWORK RECOVERY MODE
EC0BCCD4 0105133009 T H ent0 ETHERNET DOWN
F3931284 ... (4 Replies)
Discussion started by: lo-lp-kl
4 Replies
7. Solaris
my solris box network is unreachable how to solve this
ipaddress assiagning and entry in vi /etc/host
how to solve network is unreachable (2 Replies)
Discussion started by: tirupathi
2 Replies
8. AIX
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies
9. Linux
I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0.
Here's what I did:
created file /etc/modprobe.d/bonding.d and added the following to it:
alias bond0 bonding
options bonding... (2 Replies)
Discussion started by: dr_mabuse
2 Replies
LEARN ABOUT ULTRIX
ethers
ethers(5) File Formats Manual ethers(5)
Name
ethers - database that maps Ethernet addresses to hostnames
Description
The file is used in conjunction with the reverse address resolution protocol daemon, to map Ethernet addresses to hostnames. It contains
information about the known (48-bit) Ethernet addresses of hosts on the Internet.
For each host on an Ethernet, a single line should be present in the file with the following information:
Ethernet-address official-host-name
Items are separated by one or more spaces or tabs. A number sign (#) indicates the beginning of a comment that extends to the end of line.
The standard form for Ethernet addresses is:
x:x:x:x:x:x
The x is a hexadecimal number between 0 and ff, representing 1 byte. The address bytes are always in network order.
Hostnames can contain any printable character other than a space, tab, newline, or number sign (#).
Hostnames in the file should correspond to the hostnames in the file or to those provided by the name service.
Examples
The following is a sample file: 08:00:20:01:e5:1c host1 # Comments go here 08:00:20:01:d0:4c host2 # Comments go
here 08:00:20:01:e0:1d host3 # Comments go here 08:00:20:00:c2:4e host4 # Comments go here
See Also
ethers(3n), hosts(5), rarpd(8c)
Introduction to Networking and Distributed System Services
ethers(5)