Sponsored Content
Special Forums Hardware Filesystems, Disks and Memory Disk Mirroring?? have any idea??? Post 19606 by thehoghunter on Sunday 14th of April 2002 12:55:45 PM
Old 04-14-2002
Basically, it almost mandatory these days - most OS have some type of free software to do it.

Check out this link on Redhat .

Can't give you more than that since I'm not running it at the moment.

Your last question - you don't tell it to fail over - it should fail over by itself via the hardware or software (see the link).
thehoghunter
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

what is disk mirroring in unix?

Can anyone give some answers on what is disk mirroring in Unix? It may be related to unix online backup. (2 Replies)
Discussion started by: asutoshch
2 Replies

2. UNIX for Dummies Questions & Answers

Disk mirroring under RedHat 8

I would like to build a new box that has the disk mirrored to another IDE disk on a different channel. Does anyone know if a RAID controller like the Promise is supported under RedHat 8, or should I use a software RAID. (1 Reply)
Discussion started by: 98_1LE
1 Replies

3. Shell Programming and Scripting

Disk mirroring

Good Morning :) I have a new challenge to solve, I am going to write a new backup disk mirroring script. The current one, whcih is useing 'dd' caused some stalled systems :( Currently I am in the phase of experimenting with different methods, I was thinking about dump/restore afio/cpio or... (3 Replies)
Discussion started by: malcom
3 Replies

4. Solaris

Disk mirroring

Hi I have two raw disk that I want to mirror and then create soft partition on that. Could someone please help in the steps required c0t1d0 c0t0d0 Thanks Ajwat (2 Replies)
Discussion started by: Ajwat
2 Replies

5. Solaris

Help !! disk Mirroring

Hi I have a Sunfire X4100 box with a 4 disk Chassis (although I only have 2 disks in it). I have been asked to add two more disks into the chassis so that I can mirror the original two using SVM .....Ive read through a couple of SVM docs but am finding it a little confusing, and if any of you... (1 Reply)
Discussion started by: hcclnoodles
1 Replies

6. UNIX for Advanced & Expert Users

Mirroring Disk Geometry

How can one mirror disk geometry from one hard disk to another in Solaris. Is disk snapshot same as a mirror? Pls explain. (3 Replies)
Discussion started by: lexusujx
3 Replies

7. Solaris

Solaris 10 Disk Mirroring

Has anyone managed to set up disk mirroring in Solaris 10 yet? If so can you point me in the direction of some useful documentation please. Cheers (25 Replies)
Discussion started by: korfnz
25 Replies

8. Solaris

Disk Mirroring on solaris 5.8

Hi Friends, I am having Sun Solaris 5.8 OS installed having 2 different size hard disk, sizes are c0t0d0s0(160 GB) and c0t2d0s0 (40GB). I have installed Sun Solaris 5.8 OS in c0t0d0s0 (160GB) harddisk. I have configured all the parameters required for disk mirroring. But when executing... (4 Replies)
Discussion started by: Vijayakumarpc
4 Replies

9. Solaris

disk mirroring

hi every body I'm new to solaris and I need your help in how to configure disk mirroring for 4 hard disks so that two of them will be replica to the other two ...??? Thanxx (7 Replies)
Discussion started by: mm00123
7 Replies

10. Red Hat

Disk Mirroring

Hi, How to identify whether the disk is being mirrored or not in RHEL (2 Replies)
Discussion started by: gsiva
2 Replies
HD(4)							     Linux Programmer's Manual							     HD(4)

NAME
hd - MFM/IDE hard disk devices DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave hdd. General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi- cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions on an IDE disk. For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the second one. They are typically created by: mknod -m 660 /dev/hda b 3 0 mknod -m 660 /dev/hda1 b 3 1 mknod -m 660 /dev/hda2 b 3 2 ... mknod -m 660 /dev/hda8 b 3 8 mknod -m 660 /dev/hdb b 3 64 mknod -m 660 /dev/hdb1 b 3 65 mknod -m 660 /dev/hdb2 b 3 66 ... mknod -m 660 /dev/hdb8 b 3 72 chown root:disk /dev/hd* FILES
/dev/hd* SEE ALSO
chown(1), mknod(1), sd(4), mount(8) COLOPHON
This page is part of release 3.53 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/. Linux 1992-12-17 HD(4)
All times are GMT -4. The time now is 12:55 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy