Sponsored Content
Full Discussion: basic networking
Special Forums IP Networking basic networking Post 18606 by satops on Sunday 31st of March 2002 05:53:12 PM
Old 03-31-2002
I set up the windows computer with the same configuration except an ip of 192.168.0.2

I can dial out and connect to the internet with both computers (separately) now.

When I ping 192.168.0.1 from the windows computer or 192.168.0.2 from the linux box, they both time out.

I must be missing something somewhere. I had no idea this would be so difficult when I started. Any other suggestions will be appreciated.

Thanks
 

8 More Discussions You Might Find Interesting

1. Slackware

Basic networking questions.

Hey, I'm new to Linux. I have a few questions about it. I run Slackware. After the installation the Linux installation had problems with my old hardware (network card, sound card) so I removed them and Linux would start. But now, I can't seem to use the network card in Linux because it's not... (3 Replies)
Discussion started by: RellioN
3 Replies

2. UNIX for Dummies Questions & Answers

Basic networking setup in unix

I have a SunOS 5.8 box and have always downloaded & applied patches via my PC, but I want to be able to go out to sunsolve directly from the console ... however, I guess it doesn't know the IP of our domain's DNS server or something. Where are these setting held on a Sun box??? (1 Reply)
Discussion started by: FredSmith
1 Replies

3. UNIX for Advanced & Expert Users

how ..........networking

hi everyone this is dipendra, i am interested in networking,i know simple socket programming . and now i am wonder to get in to audio socket. i have no clue how to build audio socket.so i am looking if u can provide me a link regarding the audio socket building tutorials. (1 Reply)
Discussion started by: dipendra_regmi
1 Replies

4. IP Networking

C networking

Can anybody help me regarding networking using c language i know how to capture the packets and to verify it`s protocol destination and source ip etc. Can anybody help me to direct a packet coming to an ip to some other ip of my choice ........ Hope reply ... (0 Replies)
Discussion started by: Sannair
0 Replies

5. IP Networking

Networking

Hi, I have a question on networking. I will try to ask with an example... Suppose i am googling something, as in searching something in the google page. In this case what I basically want to know is, does the client do a connect evrytime to the server whenever a search is done in google,... (1 Reply)
Discussion started by: naan
1 Replies

6. IP Networking

Basic networking please help

I am running Ubuntu Desktop and Ubuntu Server editions on two separate VMs. For the desktop I have set network adapters: Adapter 1: internal network called intnet Adapter 2: NAT Server: Adapter 1: internal network called intnet Now I'm suppose to set ip addresses which I'm pretty sure... (5 Replies)
Discussion started by: shadowcat
5 Replies

7. IP Networking

Basic networking question

Hii, Today morning I attended an interview, they had showed me the attached image and had few questions about that. The image shows a network with 4 nodes viz.. A B C & D and two switches(layer2) and a router(layer3). Just wanted to know can node A and node D would be on same network e.g... (4 Replies)
Discussion started by: zing_foru
4 Replies

8. IP Networking

Networking

hi From mt windows machine I can ping a LINUX machine but there is no arp entry for the same LINUX on my windows. How is it possible and what can I do to add the arp entry as I need it. thanks (1 Reply)
Discussion started by: leghorn
1 Replies
prtdscp(1M)						  System Administration Commands					       prtdscp(1M)

NAME
prtdscp - display DSCP IP addresses SYNOPSIS
prtdscp [-v ] prtdscp [-v ] -h prtdscp [-v ] -d prtdscp [-v ] -s DESCRIPTION
prtdscp displays the IP addresses associated with a Domain to Service Processor Communications Protocol (DSCP) link. If no arguments are specified, prtdscp displays the IP addresses on both ends of the DSCP link. The IP address of either the Service Processor or domain side can be displayed separately by the use of the -s or -d options, respectively. OPTIONS
The following options are supported: -v Verbose mode. Print additional details about the program's internal progress to stderr. -h Help. Print a brief synopsis of the program's usage and exit. All other command line arguments are ignored. -d Display only the local domain's IP address. -s Display only the remote Service Processor's IP address. EXAMPLES
Example 1 Displaying both addresses The following example displays both the local domain's IP address and the remote SP's IP address: # prtdscp Domain Address: 192.168.103.2 SP Address: 192.168.103.1 Example 2 Displaying the local IP address The following example displays the local domain's IP address: # prtdscp -d 192.168.103.2 Example 3 Displaying the remote IP address The following example display the remote SP's IP address: # prtdscp -s 192.168.103.1 ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWdscpr.u, SUNWdscpu.u | +-----------------------------+-----------------------------+ |Interface Stability |Evolving | +-----------------------------+-----------------------------+ SEE ALSO
attributes(5) SunOS 5.11 25 Apr 2006 prtdscp(1M)
All times are GMT -4. The time now is 05:36 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy