Sponsored Content
Full Discussion: Solaris IPv6
Special Forums IP Networking Solaris IPv6 Post 16875 by killerserv on Thursday 7th of March 2002 08:05:13 PM
Old 03-07-2002
By default IPv6 came with the package in Solairs 8. And it functionalities are wide. Ex:

- Expanded Routing and Addressing: IPv6 increases the IP address size from 32 bits to 128 bits to support increased levels of addressing hierarchy, provide a far greater number of addressable nodes, and allow auto-configuration of addresses. Of the 128 bits, 48 bits are reserved for public topology, 16 bits to design a site topology, and 64 bits to identify a machine in a subnet. This provides support for 65K subnets with a virtually infinite number of hosts per subnet.

- IP Security: IPv6 is a better platform for implementing security through IPSec because IPv6 restores end-to-end IP connectivity. This security functionality was lost due to the introduction of NAT (Network Address Translator) boxes.

Cant figure out why you want to remove/uninstall it. I give two opinions above so that maybe you will change your mind not to uninstall.
 

9 More Discussions You Might Find Interesting

1. IP Networking

IPv6 on Solaris 10

Hi! I have to configure ipv6 network between two computers with Solaris 10 but I not an expert in using any unix system and I do it becouse I need it to my study. Is someone here who could help me and describe step-by-step how to do it? please!!! PS. I need to configure network to do secure... (1 Reply)
Discussion started by: kolec
1 Replies

2. Solaris

(Help) IPv6 tunneling over existing IPv4 in Solaris

Hi folks, i hope you'll help me to configure my ipv6 tunnel. First, i create my tunnel in: Hurricane Electric Free IPv6 Tunnel Broker My IP is 83.228.93.34 in HE: ------------------------ Server IPv4 address: 216.66.84.46 Server IPv6 address: 2001:470:1f14:16a::1/64 Client IPv4 address: ... (2 Replies)
Discussion started by: static
2 Replies

3. Solaris

Solaris 19 10/09 ipv6 interface configuration

Hi, anyone has had experience in a static setting an IPv6 interface?, I'm trying accordance with the admin guide (ipv6 network configuration tasks), configure one interface in the server, actually i can do ping to my default gateway and access the Internet in IPv6, the specific point is however,... (3 Replies)
Discussion started by: pabloluja
3 Replies

4. Solaris

checking Solaris 10 DNS server for IPv6

hi, i have a Solaris 10 DNS server, how do you check whether it can support IPv6 networking ? (0 Replies)
Discussion started by: Exposure
0 Replies

5. Solaris

Solaris 11 disable IPv6

I've new installed Solaris 11 on Sparc T4-1. I'd like to disable IPv6 but with no luck. lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 net0: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 2 inet... (6 Replies)
Discussion started by: samer.odeh
6 Replies

6. Solaris

IPv6 for Solaris DNS

I have Bind running on a Solaris box that is our main public DNS. Given my very limited knowledge on DNS, I changed a few of the zones in the DNS to be 'dual-stack'. I did it through Webmin, but I know that I can also do it by adding an AAAA-record to the zone file. My question is how can I make... (2 Replies)
Discussion started by: Dardeer
2 Replies

7. HP-UX

Ipv6 on hpux

my problem: i want to change from ipv4 to ipv6 on my home network. On hpux i can assign only address non routable as fe80::1 fe80::3 etc to my lan0 Editing netconf-ipv6 i can assing a routable ipv6 address like fd55:282f:3b98::/48 or 2001:470:26:307:89a0:aba1:f98b:eb3e but only to alias... (0 Replies)
Discussion started by: Linusolaradm1
0 Replies

8. UNIX for Dummies Questions & Answers

Assigning ipv6 to bonding interface - getting old as well as changed ipv6 in ifconfig output

Hi, I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies

9. Solaris

Solaris 10 IPv6

Hello Dears , please I need your support I have Oracle Solaris 10 X86 server please if you can advise how can I add IP v6 on my server and if IPv6 was disabled how can i enable it also how can i add two IP (v4 and v6) on the same interface or I have to add another interface . Thanks in... (1 Reply)
Discussion started by: ttashman
1 Replies
All times are GMT -4. The time now is 07:18 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy