Hi,
Fairly new to unix scripting, hoping to get some help.
using AIX v5
Basically I have 3 files 1). Header record 2). many detail record 3). Trailer record
My desired result is 1 file which contains Heaeder, Detail, Trailer
Currenty I am using a series of:
... (8 Replies)
Hi, excuse me for my poor english.
My problem is that:
I have a File
i want to add to each line of that file two strings: one at the beginning of the line, one at the ending.
string1="abcd"
string2="efgh"
i want $string1 content $string2 for each line.
Is that possible? (3 Replies)
Hi Ladies and Gents,
Explanation of my question with an example:
Let's consider the script: backup_every_hour.sh
#!/bin/bash
rsync -auv $dir $backup_dir >> backup_every_hour_script.log
Each time this script is called there will be a new entry at the end of the file... (1 Reply)
Well here goes:
I tried to write a batch file that adds a specific fixed text to each line of an already existing text file.
for the adding text infront of each line I tried this:
for /F "delims=" %%j in (list.txt) do echo.STARTTEXT\%%j >> list.txt
for adding text after each line I... (0 Replies)
Hi Guys,
I have serveral directories like this:
(2013) blablabla(blabla) - blabla (blabla)
or
(1997) blablabla(blabla) - blabla (blabla)
and have to rename them to something like that:
blablabla(blabla) - blabla (blabla) (2013)
and
blablabla(blabla) - blabla (blabla) (1997)
Easy... (2 Replies)
Hi,
I have a specific requirement to add text at the beginning and end of a plain text file. I tried to use "sed" with '1i' and '$a' flags but these required two separate "sed" commands separated with "|".
I am looking for some command/option to join these two in single command parameter.
... (6 Replies)
My file has the entries like below...
/dev/sds
/dev/sdak
/dev/sdbc
/dev/sdbu
I want to make the file like below
echo 1 > /sys/block/sds/device/rescan
echo 1 > /sys/block/sdak/device/rescan
echo 1 > /sys/block/sdbc/device/rescan
echo 1 > /sys/block/sdbu/device/rescan (2 Replies)
Hi,
I now that >> will append text to the end of the text that is already inside the file.
How to append the new text infront of the text that is already in the file.
Thanks for any input.
Regards,
Chandu (3 Replies)
Hi all and apologies for the silly question, but I've searched and I can't get this right.
I have a list of email addresses in a file that I need to blacklist (spam). the list is quite long and I would need to script a small routine so that I can get the following for each line in the file:
db... (4 Replies)
Discussion started by: bm555
4 Replies
LEARN ABOUT HPUX
networkctl
NETWORKCTL(1) networkctl NETWORKCTL(1)NAME
networkctl - Query the status of network links
SYNOPSIS
networkctl [OPTIONS...] COMMAND [LINK...]
DESCRIPTION
networkctl may be used to introspect the state of the network links as seen by systemd-networkd. Please refer to systemd-
networkd.service(8) for an introduction to the basic concepts, functionality, and configuration syntax.
OPTIONS
The following options are understood:
-a --all
Show all links with status.
-h, --help
Print a short help text and exit.
--version
Print a short version string and exit.
--no-legend
Do not print the legend, i.e. column headers and the footer with hints.
--no-pager
Do not pipe output into a pager.
COMMANDS
The following commands are understood:
list [LINK...]
Show a list of existing links and their status. If no further arguments are specified shows all links, otherwise just the specified
links. Produces output similar to:
IDX LINK TYPE OPERATIONAL SETUP
1 lo loopback carrier unmanaged
2 eth0 ether routable configured
3 virbr0 ether no-carrier unmanaged
4 virbr0-nic ether off unmanaged
4 links listed.
status [LINK...]
Show information about the specified links: type, state, kernel module driver, hardware and IP address, configured DNS servers, etc.
When no links are specified, an overall network status is shown. Also see the option --all.
Produces output similar to:
State: routable
Address: 10.193.76.5 on eth0
192.168.122.1 on virbr0
169.254.190.105 on eth0
fe80::5054:aa:bbbb:cccc on eth0
Gateway: 10.193.11.1 (CISCO SYSTEMS, INC.) on eth0
DNS: 8.8.8.8
8.8.4.4
lldp [LINK...]
Show discovered LLDP (Link Layer Discovery Protocol) neighbors. If one or more link names are specified only neighbors on those
interfaces are shown. Otherwise shows discovered neighbors on all interfaces. Note that for this feature to work, LLDP= must be turned
on on the specific interface, see systemd.network(5) for details.
Produces output similar to:
LINK CHASSIS ID SYSTEM NAME CAPS PORT ID PORT DESCRIPTION
enp0s25 00:e0:4c:00:00:00 GS1900 ..b........ 2 Port #2
Capability Flags:
o - Other; p - Repeater; b - Bridge; w - WLAN Access Point; r - Router;
t - Telephone; d - DOCSIS cable device; a - Station; c - Customer VLAN;
s - Service VLAN, m - Two-port MAC Relay (TPMR)
1 neighbors listed.
label
Show numerical address labels that can be used for address selection. This is the same information that ip-addrlabel(8) shows. See RFC
3484[1] for a discussion of address labels.
Produces output similar to:
Prefix/Prefixlen Label
::/0 1
fc00::/7 5
fec0::/10 11
2002::/16 2
3ffe::/16 12
2001:10::/28 7
2001::/32 6
::ffff:0.0.0.0/96 4
::/96 3
::1/128 0
EXIT STATUS
On success, 0 is returned, a non-zero failure code otherwise.
SEE ALSO systemd-networkd.service(8), systemd.network(5), systemd.netdev(5), ip(8)NOTES
1. RFC 3484
https://tools.ietf.org/html/rfc3484
systemd 237NETWORKCTL(1)