03-06-2002
I posted my last post before I read the previous reply. I tried using iptables, and it seems to be not working on this box. I get an error message:
"...ip_tables.o: init_module: Device or resource busy" and that insmod failed on ip_tables.o. Note that ping, ssh, telnet and ftp connectoins are all accepted and work fine.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I am very new to unix. I want to open a file and read one line in at a time. Can anybody help? (3 Replies)
Discussion started by: saarshad001
3 Replies
2. UNIX for Advanced & Expert Users
I have installed JASS on one of my sun servers.
I am now trying to open for CDE. For that I have done these steps:
mv /etc/rc2.d/_S71rpc.JASS.* /etc/rc2.d/S71rpc
mv /etc/rc2.d/_S99dtlogin.JASS* /etc/rc2.d/S99dtlogin
but still no CDE.
Any advice on this?? (3 Replies)
Discussion started by: encrypted
3 Replies
3. AIX
Hi guys,
I need to open ports on my AIX machine. The only way I know is to use service name to disable or enable ports which are used by the services. I found in /etc/services that the ports are unidentified. Btw, I want to open port number 11576 and 11577. Need help on this one. Thanks! :) (1 Reply)
Discussion started by: raskita
1 Replies
4. UNIX for Dummies Questions & Answers
I'm not sure if this is the right place for this post, but I'd be grateful if somebody could please help me. I'm trying to open ports 999, 1982 and 1983 but am not having much luck. I used
iptables -A INPUT -i eth0 -p tcp --sport 999 -m state --state NEW,ESTABLISHED -j ACCEPT
iptables -A INPUT -i... (2 Replies)
Discussion started by: thehaapyappy
2 Replies
5. IP Networking
Please can somebody help me. I'm trying to open ports 999, 1982 and 1983 but am not having much luck. I used
iptables -A INPUT -i eth0 -p tcp --sport 999 -m state --state NEW,ESTABLISHED -j ACCEPT
iptables -A INPUT -i eth0 -p tcp --sport 1982 -m state --state NEW,ESTABLISHED -j ACCEPT
iptables... (5 Replies)
Discussion started by: thehaapyappy
5 Replies
6. Solaris
Hello all,
I need assistance...
I need to open a port # 36677 and have it remain open even after a power cycle.
I thought all I needed to do was add it to /etc/services. That was not it...
Can someone please tell me how to do this.
Thank you. (6 Replies)
Discussion started by: komputersman
6 Replies
7. Solaris
I am working with Solaris 9.In that I am trying to open SMC(Solaris Management Console) but when I am clicking it,nothing is opening.
Can any1 tell me why it is not opening??:confused: (1 Reply)
Discussion started by: smartgupta
1 Replies
8. Cybersecurity
Hello there
I'm using a vendor-supplied application on RHEL4 that includes a built-in Tcl webserver. The webserver is working but I cannot access it from any computer other than the host workstation. I suspect that the firewall is blocking ports 8015/8016. I have two questions:
1. How do... (1 Reply)
Discussion started by: craig3201
1 Replies
9. UNIX for Dummies Questions & Answers
Hi,
I need a command/script, who opened my dataset, consider a situation like, if a user has opened the dataset few days back then, that command/script should list his/her id.
I don't want audit on my dataset, i need only list of users who are using my dataset.
Thank you. (10 Replies)
Discussion started by: subbarao12
10 Replies
LEARN ABOUT LINUX
ip6tables-apply
IPTABLES-APPLY(8) iptables 1.6.1 IPTABLES-APPLY(8)
NAME
iptables-apply - a safer way to update iptables remotely
SYNOPSIS
iptables-apply [-hV] [-t timeout] [-w savefile] {[rulesfile]|-c [runcmd]}
DESCRIPTION
iptables-apply will try to apply a new rulesfile (as output by iptables-save, read by iptables-restore) or run a command to configure
iptables and then prompt the user whether the changes are okay. If the new iptables rules cut the existing connection, the user will not be
able to answer affirmatively. In this case, the script rolls back to the previous working iptables rules after the timeout expires.
Successfully applied rules can also be written to savefile and later used to roll back to this state. This can be used to implement a store
last good configuration mechanism when experimenting with an iptables setup script: iptables-apply -w /etc/network/iptables.up.rules -c
/etc/network/iptables.up.run
When called as ip6tables-apply, the script will use ip6tables-save/-restore and IPv6 default values instead. Default value for rulesfile is
'/etc/network/iptables.up.rules'.
OPTIONS
-t seconds, --timeout seconds
Sets the timeout in seconds after which the script will roll back to the previous ruleset (default: 10).
-w savefile, --write savefile
Specify the savefile where successfully applied rules will be written to (default if empty string is given:
/etc/network/iptables.up.rules).
-c runcmd, --command runcmd
Run command runcmd to configure iptables instead of applying a rulesfile (default: /etc/network/iptables.up.run).
-h, --help
Display usage information.
-V, --version
Display version information.
SEE ALSO
iptables-restore(8), iptables-save(8), iptables(8).
LEGALESE
Original iptables-apply - Copyright 2006 Martin F. Krafft <madduck@madduck.net>. Version 1.1 - Copyright 2010 GW <gw.2010@tnode.com or
http://gw.tnode.com/>.
This manual page was written by Martin F. Krafft <madduck@madduck.net> and extended by GW <gw.2010@tnode.com or http://gw.tnode.com/>.
Permission is granted to copy, distribute and/or modify this document under the terms of the Artistic License 2.0.
iptables 1.6.1 IPTABLES-APPLY(8)