02-19-2002
What you need to do is to add an alias to the interface, in order to do that, do the following. First go to the file /etc/sysconfig/networking/devices/ifcfg-eth0 and add the following lines:
DEVICE=eth0:1
ONBOOT=yes
BOOTPROTO=static
IPADDR= xxx.xxx.xxx.xxx
NETMASK=xxx.xxx.xxx.xxx
GATEWAY=xxx.xxx.xxx.xxx
TYPE=Ethernet
USERCTL=no
NETWORK=xxx.xxx.xxx.xxx
BROADCAST=xxx.xxx.xxx.xxx
PEERDNS=no
Where xxx.xxx.xxx.xxx put the apropriate addresses for your computer. After doing so go to the directory /etc/rc.d/init.d and type ./network stop; ./network start. That will initiate the new configurations. You can add as many IP addresses as you want by just doing the procedures above and changing the DEVICE:eth0:x from 1 to 2,3,... etc. and also by changing the IP address.
Last edited by developer; 02-19-2002 at 01:40 PM..
10 More Discussions You Might Find Interesting
1. Linux
Had problems in configuring USB memory stick in RHL 9.
Please assist.
With regards,
Kungra. (1 Reply)
Discussion started by: kungra2006
1 Replies
2. Shell Programming and Scripting
Hi,
I want to configure 2-gateways in Linux .
Please tell me how I can achieve this. I am accesing 2-internet
connection through these 2-gateways. So I am looking that
if 1-gets down then also other one is working.
Regards
JAGDISH (1 Reply)
Discussion started by: jagdish.machhi@
1 Replies
3. Solaris
hi friends,
I have brand new Sun Ultra 20 WS installed.
It was preinstalled with Solaris 10 6/06 system,
in ifconfig -a command only loop back intervace is showing.
and
/etc/path_to_install also not able to find the interface name.
my questions are:
1. Is there any command to get... (1 Reply)
Discussion started by: subhankar
1 Replies
4. Red Hat
Hi All
when I give the command,
$ ping <hostname>
I get the following error
ping: unknown host <hostname>
I have checked in the following files,
/etc/sysconfig/network
/etc/hosts
/etc/resolv.conf
/etc/nsswitch.conf
Every where in these files host name and IP address are given... (2 Replies)
Discussion started by: nagapradeep
2 Replies
5. AIX
I have a server with multiple network interfaces. 2 of these interfaces, lets say en2 and en6 make up an etherchannel interface, which let's say en8.
when I run the command
lsattr -El ent8
I can see the designated primary and backup interfaces as ent6 and ent2, in the given order. But... (10 Replies)
Discussion started by: thenomad
10 Replies
6. UNIX for Advanced & Expert Users
Can anybody please explain the below table to monitor NTP daemon status
This contains many columns like remote,refid,st....various values corresponding to those columns
If possible provide me any link to study about these quantities clearly.
It is very much required for my project please... (3 Replies)
Discussion started by: sgand
3 Replies
7. IP Networking
i have a linux server runnig oracle applications.
i need to access this server from putty using ssh through internet.
i did by registering my static ip with the dnydns.org and i am able to connect to the server.
but now there is no security to authenticate any user as any one knowing the... (6 Replies)
Discussion started by: u.n.i.x
6 Replies
8. Infrastructure Monitoring
I am trying to enabling SNMP access and trap forwarding for Linux(RHEL5) using following official url from IBM.
http://publib.boulder.ibm.com/infocenter/eserver/v1r2/index.jsp?topic=/diricinfo/fqm0_t_enabling_snmp_access_and_trap_forwarding_for_linux.html
In my system, snmp and snmplibs are... (1 Reply)
Discussion started by: SiddhV
1 Replies
9. IP Networking
Can someone help with a detail step-by-step oh how to configure DNS server on Linux Server.
-
I need to have 3 IP addresses map to a single hostname.
for clients
I'm a Linux rookie.
Thanks
Oscar (1 Reply)
Discussion started by: FrankOscar
1 Replies
10. Red Hat
Dear Experts,
We have requirement to configure Dot matrix printer in linux, Also need to register in Oracle application R12.0.6 version where i need get the print in landscape format.
Request you all kindly help on the same.
Thank you,
Alone.
---------- Post updated 02-18-14 at 01:02... (6 Replies)
Discussion started by: Alone
6 Replies
LEARN ABOUT OPENSOLARIS
addpart
ADDPART(8) System Administration ADDPART(8)
NAME
addpart - tell the kernel about the existence of a partition
SYNOPSIS
addpart device partition start length
DESCRIPTION
addpart tells the Linux kernel about the existence of the specified partition. The command is a simple wrapper around the "add partition"
ioctl.
This command doesn't manipulate partitions on a block device.
PARAMETERS
device The disk device.
partition
The partition number.
start The beginning of the partition (in 512-byte sectors).
length The length of the partition (in 512-byte sectors).
SEE ALSO
delpart(8), fdisk(8), parted(8), partprobe(8), partx(8)
AVAILABILITY
The addpart command is part of the util-linux package and is available from https://www.kernel.org/pub/linux/utils/util-linux/.
util-linux January 2015 ADDPART(8)