02-18-2002
I am new at Unix stuff... so I am not really sure what you are not able to do, but I am guessing that you cannot see the network.
Can you ping the gateway (router) IP? If not you may not have a default route pointing to the gateway.
Steve
10 More Discussions You Might Find Interesting
1. IP Networking
I am trying to network an SGI running Irix 6.5 through an ethernet line to a PC running Windows 2000 (I have connected other PC's to this PC without any problems.) The PC has a DSL connection from Verizon that does not support Unix. I tried using DHCP on the SGI, but when I open a web browser on... (2 Replies)
Discussion started by: mdbanas
2 Replies
2. IP Networking
anyone available to help me config sgi octane to netscape and networking mac os X?
i have three macs and one sgi. setup on a dsl netopia router.
all 4 computers can ping each other by addresses and by names.
all the macs can ping the router, but the sgi cannot ping the router, "network is... (0 Replies)
Discussion started by: eidde
0 Replies
3. Solaris
To begin with, I am a Solaris newbie; however, I am very familiar with Linux. Until I began working with Solaris, I didn't realize how much more difficult networking Solaris is than Linux. Before submitting this question, I have tried to fix this problem myself. After days of research, I still... (3 Replies)
Discussion started by: cstovall
3 Replies
4. IP Networking
I have a linksys router BEFSR41. I am trying to connect two network..
one device has to route from one network of IP address 192.168.10.12 to go to a device on separate network with IP address 192.168.25.95.
In the configuration LAN ip address by default it 192.168.1.1
If I define LAN IP to... (0 Replies)
Discussion started by: ajnabi
0 Replies
5. IP Networking
I just sys-unconfigged my ultra sparc which is on my home network where I have 2 PCs attached. When I go to install Solaris 8, it asks various things re: networking. Specifically, when it asks for the IP addy for the DNS server, I input the info, but it barfs back "IP addy info not found". I... (10 Replies)
Discussion started by: nicomen
10 Replies
6. Shell Programming and Scripting
I'm trying to use wget to submit a form. I have tried to dig out what is actually being "posted" and where, using tamperdata (see below).
http://ubuntuforums.org/attachment.php?attachmentid=109123&d=1239224127
Here is my wget command:
wget --http-user=xyz --http-password=xyz... (1 Reply)
Discussion started by: mike909
1 Replies
7. IP Networking
Does anyone know if this router can restrict incoming traffic to specific IP addresses. There does not seem to be any information on Cisco's web site any more.
ie Only 209.123.123.123 is allowed access to port 9100, which is redirected to 192.168.1.100 (1 Reply)
Discussion started by: jgt
1 Replies
8. Cybersecurity
Hi
I have very basic network settings in my home. Cable connected to my Linksys Wireless G router. My wife and I connect to that using our laptop.
Yes. I did enable encryption to connect. Also my wireless printer is connected to that.
For some reason, last night around 12:30 AM, the... (4 Replies)
Discussion started by: samnyc
4 Replies
9. UNIX for Dummies Questions & Answers
I configured my linux server with Static IP address out of the range of the DHCP linksys router, but cannot get on the internet.
When I switch back to "Automatically obtain IP address" ..then I can get on the internet.
Can comeone help with this. (2 Replies)
Discussion started by: FrankOscar
2 Replies
10. Hardware
Hello.
I have a sun v245 and I have no hard drive for it yet but i would like to connect it to my home router by ethernet cable so I can use Alom remotely. Could someone please tell me how to set it up.
Thank You (1 Reply)
Discussion started by: SunV245
1 Replies
LEARN ABOUT REDHAT
perlirix
PERLIRIX(1) Perl Programmers Reference Guide PERLIRIX(1)
NAME
README.irix - Perl version 5 on Irix systems
DESCRIPTION
This document describes various features of Irix that will affect how Perl version 5 (hereafter just Perl) is compiled and/or runs.
Building 32-bit Perl in Irix
Use
sh Configure -Dcc='cc -n32'
to compile Perl 32-bit. Don't bother with -n32 unless you have 7.1 or later compilers (use cc -version to check).
(Building 'cc -n32' is the default.)
Building 64-bit Perl in Irix
Use
sh Configure -Dcc='cc -64' -Duse64bitint
This requires require a 64-bit MIPS CPU (R8000, R10000, ...)
You can also use
sh Configure -Dcc='cc -64' -Duse64bitall
but that makes no difference compared with the -Duse64bitint because of the "cc -64".
You can also do
sh Configure -Dcc='cc -n32' -Duse64bitint
to use long longs for the 64-bit integer type, in case you don't have a 64-bit CPU.
If you are using gcc, just
sh Configure -Dcc=gcc -Duse64bitint
should be enough, the Configure should automatically probe for the correct 64-bit settings.
About Compiler Versions of Irix
Some Irix cc versions, e.g. 7.3.1.1m (try cc -version) have been known to have issues (coredumps) when compiling perl.c. If you've used
-OPT:fast_io=ON and this happens, try removing it. If that fails, or you didn't use that, then try adjusting other optimization options
(-LNO, -INLINE, -O3 to -O2, etcetera). The compiler bug has been reported to SGI. (Allen Smith <easmith@beatrice.rutgers.edu>)
Linker Problems in Irix
If you get complaints about so_locations then search in the file hints/irix_6.sh for "lddflags" and do the suggested adjustments. (David
Billinghurst <David.Billinghurst@riotinto.com.au>)
Malloc in Irix
Do not try to use Perl's malloc, this will lead into very mysterious errors (especially with -Duse64bitall).
Building with threads in Irix
Run Configure with -Duseithreads which will configure Perl with the new Perl 5.8.0 "interpreter threads", see threads.
The old Perl 5.005 threads is obsolete, unmaintained, and its use is discouraged. If you really want it, run Configure with the
-Dusethreads -Duse5005threads options as described in INSTALL.
For either thread model and for Irix 6.2, you have to have the following patches installed:
1404 Irix 6.2 Posix 1003.1b man pages
1645 Irix 6.2 & 6.3 POSIX header file updates
2000 Irix 6.2 Posix 1003.1b support modules
2254 Pthread library fixes
2401 6.2 all platform kernel rollup
IMPORTANT: Without patch 2401, a kernel bug in Irix 6.2 will cause your machine to panic and crash when running threaded perl. Irix 6.3
and later are okay.
Thanks to Hannu Napari <Hannu.Napari@hut.fi> for the IRIX
pthreads patches information.
AUTHOR
Jarkko Hietaniemi <jhi@iki.fi>
Please report any errors, updates, or suggestions to perlbug@perl.org.
perl v5.8.0 2003-02-18 PERLIRIX(1)