02-11-2002
Move a disk to Sol. 2.6
I removed an external Sun disk (with data on it) from an old 2.6 system and added the disk to another 2.6 system. The new system seems to recognize the system (verified by the format command).
When try to mount I am getting, I got the error:
mount: /dev/dsk/c1t1d0s6 is not this fstype.
I then tried to fsck and get the following error:
BAD SUPER BLOCK: MAGIC NUMBER WRONG
USE AN ALTERNATE SUPER-BLOCK TO SUPPLY NEEDED INFORMATION;
I used the newfs -Nv to find out alternate superblock info. and still I got the same above error.
TIA
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
I was using an external SCSI disk on a Sun Ultra60 (Solaris 7) as the boot device. It was labelled c1t0d0. I then moved it into the internal removable mounts and it should become c0t0d0, but it apparently didn't change properly. When the machine boots, it gets host information from the disk... (2 Replies)
Discussion started by: Solaris
2 Replies
2. Solaris
Hi,
I need to do an installation where I have identical hardware at both sites and create the installation at one site and take the disk to the other site. Question: Do I need to do anything special for the OS to come up properly?
thanks. (18 Replies)
Discussion started by: VirginiaSA
18 Replies
3. UNIX for Advanced & Expert Users
Greetings Forumers!
I ran into an issue after running luupgrade on v880 running Solaris 8. I want to upgrade to Solaris 10.
When I rebooted the system I noticed the file systems listed as such:
# df -h
Filesystem size used avail capacity Mounted on
/dev/dsk/c1t1d0s0 ... (2 Replies)
Discussion started by: bluescreen
2 Replies
4. Solaris
I'm getting ready to start a LU from Sol 9 to Solaris 10. I want to ensure that I have enough disk space for future upgrades. What I don't know is what free space Solaris requires.
If I have 10GB of free space in /opt, will Solaris 10 use that for a LU?
Or, do I need to allocate 10GB of space... (5 Replies)
Discussion started by: zeekstern
5 Replies
5. Solaris
Hi,
The disks of my servers are getting full and I need to move the /export/home partition on to a new set of disks. I already have 2 mirrored disks and have added 2 more and mirrored them after creating the filesystem on them.
Do I just need to edit the /etc/vfstab and point the /export/home... (1 Reply)
Discussion started by: run_time_error
1 Replies
6. Solaris
Do I need to reinstall/rerun JASS after upgrading from Sol9 to Sol10?
Just wondered if the upgrade procedure overwrote any of the settings etc? (0 Replies)
Discussion started by: psychocandy
0 Replies
7. Solaris
I'd like to finish setting up this system and then move the secondary or primary disk to another system that is the exact same hardware.
I've done things like this in the past with ufs and disk suite mirroring just fine. But I have yet to do it with a zfs root pool mirror.
Are there any... (1 Reply)
Discussion started by: Metasin
1 Replies
8. UNIX for Dummies Questions & Answers
Hi,
I have server with 2 active disk, but disk 1 contain big part of os is falling,
how can i move everything to disk 2 and then remove the disk 1?
Thanks (4 Replies)
Discussion started by: prpkrk
4 Replies
9. Linux
Hi
We have RHEL 7.3 running from local disk and we want to move it to storage.
I am unable to find any proper procedure to do this activity. Please help. (4 Replies)
Discussion started by: powerAIX
4 Replies
10. Solaris
We have in a couple of occasions moved root disk & flashcard in netra 240 to new identical hardware instead of replacing mb in dead server. Flashcard is to preserve mac adresses and mainly hostid for license stuff. Works without doing anything other than poweron & boot.
Now we have a similar... (5 Replies)
Discussion started by: stockhes
5 Replies
LEARN ABOUT HPUX
acctresume
acctsuspend(5) File Formats Manual acctsuspend(5)
NAME
acctsuspend, acctresume - suspend and resume accounting when available disk space reaches threshold
VALUES
Failsafe
Default.
Default
acctsuspend:
acctresume:
Allowed values
acctresume:
acctsuspend:
Recommended values
acctsuspend:
acctresume: (But more than acctsuspend)
DESCRIPTION
The and tunables control when accounting stops and resumes due to disk space constraints. When free disk space on the file system being
used by accounting reaches the suspension threshold, which is the percentage relative to the percentage of disk space available only to the
superuser, accounting is suspended until such time as the free disk space reaches the resumption threshold, which is the percentage rela-
tive to the percentage of disk space available only to the superuser.
Note: Since the and values are specified relative to the percentage of disk space available only to the superuser, negative values
of these parameters can make sense. For example, if the superuser has reserved 10 percent of the disk space on the file system at
file system creation time, and acctsuspend is -5 and acctresume is 0, the suspension threshold will be 5 percent of the total disk
space and the resumption threshold will be 10 percent of the total disk space.
Who Is Expected to Change This Tunable?
Anyone using accounting.
Restrictions on Changing
Changes to this tunable take effect at the next reboot.
When Should the Value of This Tunable Be Raised?
Increasing either variable should be considered when it is necessary to maintain a higher percentage of free space on the accounting
filesystem.
What Are the Side Effects of Raising the Value of This Tunable?
The higher either value is, the less accounting data may be captured. The further the values are separated, the greater the amount of
potentially lost accounting data.
When Should the Value of This Tunable Be Lowered?
If additional disk space is needed for accounting data, and it cannot be obtained by moving files off of the filesystem, then the value of
should be lowered.
What Are the Side Effects of Lowering the Value of This Tunable?
Filesystem performance (writing accounting records) decreases as the filesystem fills up. In turn, this will decrease the overall perfor-
mance of accounting processes.
What Other Tunables Should Be Changed at the Same Time?
When changing either of these tunables, both should be considered.
WARNINGS
All HP-UX kernel tunable parameters are release specific. This parameter may be removed or have its meaning changed in future releases of
HP-UX.
Installation of optional kernel software, from HP or other vendors, may cause changes to tunable parameter values. After installation,
some tunable parameters may no longer be at the default or recommended values. For information about the effects of installation on tun-
able values, consult the documentation for the kernel software being installed. For information about optional kernel software that was
factory installed on your system, see at
AUTHOR
and were developed by HP.
SEE ALSO
accton(1M).
Tunable Kernel Parameters acctsuspend(5)