02-10-2002
9 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies
3. Solaris
Hi All,
i have a problem with my database server using sun machine v440 and sunOS 5.9 on ethernet, i've checked on system log /var/adm/messages and found much error messages like shown below :
Sep 21 16:14:48 dbs genunix: WARNING: ce0: fault detected external to device; service degraded
Sep... (2 Replies)
Discussion started by: bucci
2 Replies
4. Solaris
Hey. i have been trying to configure the on board Ethernet in My Sparcstation 5, i have spent a lot of time on the ifconfig man pages. but it could really be nice with some pro. help. i don't think the interface is running . i don't know what name the interface have, le0 eth0 et0, it just says no... (4 Replies)
Discussion started by: mads-nielsen
4 Replies
5. UNIX for Dummies Questions & Answers
I did a netstat -an and saw that ntp was listening on 4 UDP ports for each interface. Is this insecure because they are UDP ports and I don't see them in a listen state, is that because they are just a client.
Thank you.
*.ntp Idle... (2 Replies)
Discussion started by: csross
2 Replies
6. Solaris
Hi,
During the installation of solaris suppose I am configuring one ethernet interface that is primary but on my server there are 4 ethernet interfaces,because all other interface not configured,
what is way to find out how many ethernet interfaces are there on Server, (6 Replies)
Discussion started by: manoj.solaris
6 Replies
7. Solaris
hi all,
i start with solaris 11 and i am disapointed by the change on ip managing.
i want to set a ipmp over tow aggregate but i dont find any doc and i am lost with the new commande
switch1
net0 aggregate1 |
net1 aggregate1 |-----|
|... (1 Reply)
Discussion started by: sylvain
1 Replies
8. AIX
Hello Everyone,
Quick question, any short and fast way to locate and map the physical Ethernet ports on the physical server ?
Server with expansion box has around 12 ethernet ports (fibre and ethernet)
what is the quickest way to map or find out en0 represents which physical port ?
... (1 Reply)
Discussion started by: filosophizer
1 Replies
9. Solaris
I have a server with 6 Ethernet ports. 4 are the the motherboard based 1 GBE ports and 2 are 10 GBE ports on NICs.
I have set these all up with static IP addresses and use the standard /etc/nsswitch.files. My IP addresses are
net0 192.168.1.82
net1 192.168.2.82
and so on till
net5... (4 Replies)
Discussion started by: ashlaw
4 Replies
LEARN ABOUT FREEBSD
rtquery
RTQUERY(8) BSD System Manager's Manual RTQUERY(8)
NAME
rtquery -- query routing daemons for their routing tables
SYNOPSIS
rtquery [-np1] [-w timeout] [-r addr] [-a secret] host ...
rtquery [-t op] host ...
DESCRIPTION
The rtquery utility is used to query a RIP network routing daemon, such as routed(8), for its routing table by sending a request or poll com-
mand. The routing information in any routing response packets returned is displayed numerically and symbolically.
The rtquery utility by default uses the request command. When the -p option is specified, rtquery uses the poll command, an undocumented
extension to the RIP protocol supported by the commercial gated routing product. When querying gated, the poll command is preferred over the
request command because the response is not subject to Split Horizon and/or Poisoned Reverse, and because some versions of gated do not
answer the request command. The routed(8) utility does not answer the poll command, but recognizes requests coming from rtquery and so
answers completely.
The rtquery utility is also used to turn tracing on or off in routed(8).
The following options are available:
-n displays only the numeric network and host numbers instead of both numeric and symbolic.
-p uses the poll command to request full routing information from gated. This is an undocumented extension RIP protocol supported only
by gated.
-1 queries using RIP version 1 instead of RIP version 2.
-w timeout
changes the delay for an answer from each host. By default, each host is given 15 seconds to respond.
-r addr
asks about the route to destination addr.
-a passwd=XXX
-a md5_passwd=XXX|KeyID
causes the query to be sent with the indicated cleartext or MD5 password.
-t op changes tracing, where op is one of the following. Requests from processes not running with UID 0 or on distant networks are gener-
ally ignored by the daemon except for a message in the system log. gated is likely to ignore these debugging requests.
on=tracefile
turns tracing on into the specified file. That file must usually have been specified when the daemon was started or be the
same as a fixed name, often /etc/routed.trace.
more increases the debugging level.
off turns off tracing.
dump dumps the daemon's routing table to the current tracefile.
SEE ALSO
routed(8)
Routing Information Protocol, RIPv1, RFC1058.
Routing Information Protocol, RIPv2, RFC1723.
BSD
June 1, 1996 BSD