Sponsored Content
Top Forums UNIX for Dummies Questions & Answers aggregate ethernet ports under Solaris Post 15087 by wizard on Saturday 9th of February 2002 10:27:12 PM
Old 02-09-2002
For Solaris 7 or earlier, look at Sun Trunking software. Make sure your switch is compatible with Sun Trunking software. If you are running Solaris 8 10/00 or later, you can use IP multi-pathing which is built into the kernel. Look at http://www.sun.com/docs and search for IP multi-pathing.
 

9 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies

2. IP Networking

Solaris 9 Ethernet Card Problems

I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem? I am using the command: ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies

3. Solaris

[Please Help] ethernet problem on solaris

Hi All, i have a problem with my database server using sun machine v440 and sunOS 5.9 on ethernet, i've checked on system log /var/adm/messages and found much error messages like shown below : Sep 21 16:14:48 dbs genunix: WARNING: ce0: fault detected external to device; service degraded Sep... (2 Replies)
Discussion started by: bucci
2 Replies

4. Solaris

Configuring TP Ethernet in SPARCstation 5 Solaris 8

Hey. i have been trying to configure the on board Ethernet in My Sparcstation 5, i have spent a lot of time on the ifconfig man pages. but it could really be nice with some pro. help. i don't think the interface is running . i don't know what name the interface have, le0 eth0 et0, it just says no... (4 Replies)
Discussion started by: mads-nielsen
4 Replies

5. UNIX for Dummies Questions & Answers

NTP idle ports and ethernet interfaces

I did a netstat -an and saw that ntp was listening on 4 UDP ports for each interface. Is this insecure because they are UDP ports and I don't see them in a listen state, is that because they are just a client. Thank you. *.ntp Idle... (2 Replies)
Discussion started by: csross
2 Replies

6. Solaris

Sun Solaris ethernet interface

Hi, During the installation of solaris suppose I am configuring one ethernet interface that is primary but on my server there are 4 ethernet interfaces,because all other interface not configured, what is way to find out how many ethernet interfaces are there on Server, (6 Replies)
Discussion started by: manoj.solaris
6 Replies

7. Solaris

IPMP over aggregate in Solaris 11

hi all, i start with solaris 11 and i am disapointed by the change on ip managing. i want to set a ipmp over tow aggregate but i dont find any doc and i am lost with the new commande switch1 net0 aggregate1 | net1 aggregate1 |-----| |... (1 Reply)
Discussion started by: sylvain
1 Replies

8. AIX

Locating and Mapping Physical Ethernet Ports

Hello Everyone, Quick question, any short and fast way to locate and map the physical Ethernet ports on the physical server ? Server with expansion box has around 12 ethernet ports (fibre and ethernet) what is the quickest way to map or find out en0 represents which physical port ? ... (1 Reply)
Discussion started by: filosophizer
1 Replies

9. Solaris

Solaris 11 ssh on machine with multiple Ethernet ports

I have a server with 6 Ethernet ports. 4 are the the motherboard based 1 GBE ports and 2 are 10 GBE ports on NICs. I have set these all up with static IP addresses and use the standard /etc/nsswitch.files. My IP addresses are net0 192.168.1.82 net1 192.168.2.82 and so on till net5... (4 Replies)
Discussion started by: ashlaw
4 Replies
URI::URL(3)						User Contributed Perl Documentation					       URI::URL(3)

NAME
URI::URL - Uniform Resource Locators SYNOPSIS
$u1 = URI::URL->new($str, $base); $u2 = $u1->abs; DESCRIPTION
This module is provided for backwards compatibility with modules that depend on the interface provided by the "URI::URL" class that used to be distributed with the libwww-perl library. The following differences exist compared to the "URI" class interface: o The URI::URL module exports the url() function as an alternate constructor interface. o The constructor takes an optional $base argument. The "URI::URL" class is a subclass of "URI::WithBase". o The URI::URL->newlocal class method is the same as URI::file->new_abs. o URI::URL::strict(1) o $url->print_on method o $url->crack method o $url->full_path: same as ($uri->abs_path || "/") o $url->netloc: same as $uri->authority o $url->epath, $url->equery: same as $uri->path, $uri->query o $url->path and $url->query pass unescaped strings. o $url->path_components: same as $uri->path_segments (if you don't consider path segment parameters) o $url->params and $url->eparams methods o $url->base method. See URI::WithBase. o $url->abs and $url->rel have an optional $base argument. See URI::WithBase. o $url->frag: same as $uri->fragment o $url->keywords: same as $uri->query_keywords o $url->localpath and friends map to $uri->file. o $url->address and $url->encoded822addr: same as $uri->to for mailto URI o $url->groupart method for news URI o $url->article: same as $uri->message SEE ALSO
URI, URI::WithBase COPYRIGHT
Copyright 1998-2000 Gisle Aas. perl v5.18.2 2012-02-11 URI::URL(3)
All times are GMT -4. The time now is 12:13 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy