aggregate ethernet ports under Solaris Post: 15087

9 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this?

2. IP Networking

Solaris 9 Ethernet Card Problems

I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem? I am using the command: ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up I am running Solaris 9 OS.

3. Solaris

[Please Help] ethernet problem on solaris

Hi All, i have a problem with my database server using sun machine v440 and sunOS 5.9 on ethernet, i've checked on system log /var/adm/messages and found much error messages like shown below : Sep 21 16:14:48 dbs genunix: WARNING: ce0: fault detected external to device; service degraded Sep...

4. Solaris

Configuring TP Ethernet in SPARCstation 5 Solaris 8

Hey. i have been trying to configure the on board Ethernet in My Sparcstation 5, i have spent a lot of time on the ifconfig man pages. but it could really be nice with some pro. help. i don't think the interface is running . i don't know what name the interface have, le0 eth0 et0, it just says no...

5. UNIX for Dummies Questions & Answers

NTP idle ports and ethernet interfaces

I did a netstat -an and saw that ntp was listening on 4 UDP ports for each interface. Is this insecure because they are UDP ports and I don't see them in a listen state, is that because they are just a client. Thank you. *.ntp Idle...

6. Solaris

Sun Solaris ethernet interface

Hi, During the installation of solaris suppose I am configuring one ethernet interface that is primary but on my server there are 4 ethernet interfaces,because all other interface not configured, what is way to find out how many ethernet interfaces are there on Server,

7. Solaris

IPMP over aggregate in Solaris 11

hi all, i start with solaris 11 and i am disapointed by the change on ip managing. i want to set a ipmp over tow aggregate but i dont find any doc and i am lost with the new commande switch1 net0 aggregate1 | net1 aggregate1 |-----| |...

8. AIX

Locating and Mapping Physical Ethernet Ports

Hello Everyone, Quick question, any short and fast way to locate and map the physical Ethernet ports on the physical server ? Server with expansion box has around 12 ethernet ports (fibre and ethernet) what is the quickest way to map or find out en0 represents which physical port ? ...

9. Solaris

Solaris 11 ssh on machine with multiple Ethernet ports

I have a server with 6 Ethernet ports. 4 are the the motherboard based 1 GBE ports and 2 are 10 GBE ports on NICs. I have set these all up with static IP addresses and use the standard /etc/nsswitch.files. My IP addresses are net0 192.168.1.82 net1 192.168.2.82 and so on till net5...

LEARN ABOUT SUNOS

grub

grub(5) 																   grub(5)

NAME

       grub - GRand Unified Bootloader software on Solaris

       The  current  release  of the Solaris operating system is shipped with the GRUB (GRand Unified Bootloader) software.  GRUB is developed and
       supported by the Free Software Foundation.

       The overview for the GRUB Manual, accessible at www.gnu.org, describes GRUB:

	      Briefly, a boot loader is the first software program that runs when a computer starts. It is responsible for loading  and  transfer-
	      ring  control  to  an operating system kernel software (such as Linux or GNU Mach). The kernel, in turn, initializes the rest of the
	      operating system (for example, a GNU [Ed. note: or Solaris] system).

	      GNU GRUB is a very powerful boot loader that can load a wide variety of free, as well as proprietary, operating systems, by means of
	      chain-loading.  GRUB  is	designed  to  address  the complexity of booting a personal computer; both the program and this manual are
	      tightly bound to that computer platform, although porting to other platforms may be addressed in the  future.  [Ed.  note:  Sun  has
	      ported GRUB to the Solaris operating system.]

	      One of the important features in GRUB is flexibility; GRUB understands filesystems and kernel executable formats, so you can load an
	      arbitrary operating system the way you like, without recording the physical position of your kernel on the disk. Thus you  can  load
	      the kernel just by specifying its file name and the drive and partition where the kernel resides.

       Among  Solaris  machines, GRUB is supported on  platforms. The GRUB software that is shipped with Solaris adds two utilities not present in
       the open-source distribution:

       bootadm(1M)

	   Enables you to manage the boot archive and make changes to the GRUB menu.

       installgrub(1M)

	   Loads the boot program from disk.

       Both of these utilities are described in Solaris man pages.

       Beyond these two Solaris-specific utilities, the GRUB software is described in the GRUB manual, a PDF version of which  is  available  from
       the Sun web site.  Available in the same location is the grub(8) open-source man page.  This man page describes the GRUB shell.

       boot(1M), bootadm(1M), installgrub(1M)

       http://www.gnu.org/software/grub

								    21 Apr 2005 							   grub(5)