02-09-2002
aggregate ethernet ports under Solaris
I have been looking for info on how to aggregate 2 ore 3 NIC's into into one big pipe. Any advice would be appreciated.
-Chuck
9 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies
3. Solaris
Hi All,
i have a problem with my database server using sun machine v440 and sunOS 5.9 on ethernet, i've checked on system log /var/adm/messages and found much error messages like shown below :
Sep 21 16:14:48 dbs genunix: WARNING: ce0: fault detected external to device; service degraded
Sep... (2 Replies)
Discussion started by: bucci
2 Replies
4. Solaris
Hey. i have been trying to configure the on board Ethernet in My Sparcstation 5, i have spent a lot of time on the ifconfig man pages. but it could really be nice with some pro. help. i don't think the interface is running . i don't know what name the interface have, le0 eth0 et0, it just says no... (4 Replies)
Discussion started by: mads-nielsen
4 Replies
5. UNIX for Dummies Questions & Answers
I did a netstat -an and saw that ntp was listening on 4 UDP ports for each interface. Is this insecure because they are UDP ports and I don't see them in a listen state, is that because they are just a client.
Thank you.
*.ntp Idle... (2 Replies)
Discussion started by: csross
2 Replies
6. Solaris
Hi,
During the installation of solaris suppose I am configuring one ethernet interface that is primary but on my server there are 4 ethernet interfaces,because all other interface not configured,
what is way to find out how many ethernet interfaces are there on Server, (6 Replies)
Discussion started by: manoj.solaris
6 Replies
7. Solaris
hi all,
i start with solaris 11 and i am disapointed by the change on ip managing.
i want to set a ipmp over tow aggregate but i dont find any doc and i am lost with the new commande
switch1
net0 aggregate1 |
net1 aggregate1 |-----|
|... (1 Reply)
Discussion started by: sylvain
1 Replies
8. AIX
Hello Everyone,
Quick question, any short and fast way to locate and map the physical Ethernet ports on the physical server ?
Server with expansion box has around 12 ethernet ports (fibre and ethernet)
what is the quickest way to map or find out en0 represents which physical port ?
... (1 Reply)
Discussion started by: filosophizer
1 Replies
9. Solaris
I have a server with 6 Ethernet ports. 4 are the the motherboard based 1 GBE ports and 2 are 10 GBE ports on NICs.
I have set these all up with static IP addresses and use the standard /etc/nsswitch.files. My IP addresses are
net0 192.168.1.82
net1 192.168.2.82
and so on till
net5... (4 Replies)
Discussion started by: ashlaw
4 Replies
LEARN ABOUT OPENSOLARIS
posix_fadvise
posix_fadvise(3C) Standard C Library Functions posix_fadvise(3C)
NAME
posix_fadvise - file advisory information
SYNOPSIS
#include <fcntl.h>
int posix_fadvise(int fd, off_t offset, off_t len, int advice);
DESCRIPTION
The posix_fadvise() function advises the system on the expected behavior of the application with respect to the data in the file associated
with the open file descriptor, fd, starting at offset and continuing for len bytes. The specified range need not currently exist in the
file. If len is zero, all data following offset is specified. The system may use this information to optimize handling of the specified
data. The posix_fadvise() function has no effect on the semantics of other operations on the specified data, although it may affect the
performance of other operations.
The advice to be applied to the data is specified by the advice parameter and may be one of the following values:
POSIX_FADV_NORMAL Specifies that the application has no advice to give on its behavior with respect to the specified data. It is the
default characteristic if no advice is given for an open file.
POSIX_FADV_SEQUENTIAL Specifies that the application expects to access the specified data sequentially from lower offsets to higher off-
sets.
POSIX_FADV_RANDOM Specifies that the application expects to access the specified data in a random order.
POSIX_FADV_WILLNEED Specifies that the application expects to access the specified data in the near future.
POSIX_FADV_DONTNEED Specifies that the application expects that it will not access the specified data in the near future.
POSIX_FADV_NOREUSE Specifies that the application expects to access the specified data once and then not reuse it thereafter.
These values are defined in <fcntl.h>
RETURN VALUES
Upon successful completion, posix_fadvise() returns zero. Otherwise, an error number is returned to indicate the error.
ERRORS
The posix_fadvise() function will fail if:
EBADF The fd argument is not a valid file descriptor.
EINVAL The value of advice is invalid, or the value of len is less than zero.
ESPIPE The fd argument is associated with a pipe or FIFO.
USAGE
The posix_fadvise() function has a transitional interface for 64-bit file offsets. See lf64(5).
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Interface Stability |Committed |
+-----------------------------+-----------------------------+
|MT-Level |MT-Safe |
+-----------------------------+-----------------------------+
|Standard |See standards(5). |
+-----------------------------+-----------------------------+
SEE ALSO
posix_madvise(3C), attributes(5), standards(5)
SunOS 5.11 14 Jul 2008 posix_fadvise(3C)