|
|
Sponsored Content
Top Forums
UNIX for Dummies Questions & Answers
My network card wasn't recognised
Post 15044 by adam_crosby on Saturday 9th of February 2002 01:26:17 AM
02-09-2002
A 3com 3c59x card /should/ have been detected during install by Redhat 7. Are you certain the card is functional? If you've modified your kernel in anyway, make sure you have the vortex/boomerang driver installed, as Neo said. Here's a detailed link to all things Linux and 3com NICs 
http://www.scyld.com/network/vortex.html
http://www.scyld.com/network/vortex.html
|
|
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. Shell Programming and Scripting
I wonder how I shall read the result below, especially 'what'
shown below.
The result was shown when I entered 'w'.
E.g what is TOP? What is gosh ( what does selmgr mean?)?
login@ idle JCPU PCPU what
6:15am 7:04 39 39 TOP
6:34am 6:45 45 45 TOP
6:41am ... (1 Reply)
Discussion started by: Aelgen
1 Replies
3. IP Networking
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
Discussion started by: DPAI
0 Replies
4. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
5. UNIX for Advanced & Expert Users
Somehow someone created a file named '-ov' in the root directory.
Given the name, the how was probably the result of some cpio command they bozo'ed.
I've tried a number of different ways to get rid of it using * and ? wildcards, '\' escape patterns etc.. They all fail with " illegal option --... (3 Replies)
Discussion started by: GSalisbury
3 Replies
6. UNIX for Advanced & Expert Users
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies
7. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
8. Solaris
Hi Experts,
Can we use some command from unix to find the available network interface? I did tried
Its listing following, however how can I decide the which vender card is attached
e.g. if its hme , bge or some thing else
Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies
9. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
10. Ubuntu
Hi
Please can you help me to understand what could be wrong based on what I have captured in the logs:
I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed.
Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies
LEARN ABOUT OPENSOLARIS
purple-url-handler
purple-url-handler(1) User Commands purple-url-handler(1) NAME
purple-url-handler - Python script to handle URL with purple SYNOPSIS
purple-url-handler [-URL] DESCRIPTION
Python script to handle URL with purple. OPTIONS
Usage: purple-url-handler URL Example: purple-url-handler "xmpp:romeo@montague.net?message" ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWgnome-im-client | +-----------------------------+-----------------------------+ |Interface stability |Volatile | +-----------------------------+-----------------------------+ SEE ALSO
purple-remote(1), purple-send(1), purple-send-async(1), attributes(5) purple-url-handler Manual, http://pidgin.im/ NOTES
Updated by Lei Ju, Sun Microsystems Inc., 2006, 2007. SunOS 5.11 02 Apr 2008 purple-url-handler(1)