Sponsored Content
Top Forums UNIX for Dummies Questions & Answers My network card wasn't recognised Post 14808 by Neo on Wednesday 6th of February 2002 07:41:17 PM
Old 02-06-2002
Rebuild the kernel with the proper network card enabled. After building the kernel, build the modules. Install both the kernel and the modules. That's it in a nutshell.
 

10 More Discussions You Might Find Interesting

1. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies

2. Shell Programming and Scripting

Clearify what it means under 'WHAT' when hit the 'w'-command

I wonder how I shall read the result below, especially 'what' shown below. The result was shown when I entered 'w'. E.g what is TOP? What is gosh ( what does selmgr mean?)? login@ idle JCPU PCPU what 6:15am 7:04 39 39 TOP 6:34am 6:45 45 45 TOP 6:41am ... (1 Reply)
Discussion started by: Aelgen
1 Replies

3. IP Networking

Network Card with SGI

The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out > link ok < when i connected > But... (0 Replies)
Discussion started by: DPAI
0 Replies

4. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies

5. UNIX for Advanced & Expert Users

How to remove a file with a leading dash '-' in it's name?

Somehow someone created a file named '-ov' in the root directory. Given the name, the how was probably the result of some cpio command they bozo'ed. I've tried a number of different ways to get rid of it using * and ? wildcards, '\' escape patterns etc.. They all fail with " illegal option --... (3 Replies)
Discussion started by: GSalisbury
3 Replies

6. UNIX for Advanced & Expert Users

network card problem

hi, everyone: alpha 600 au true64 Unix 4.0f my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages. "tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies

7. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies

8. Solaris

How to identifying the network card ?

Hi Experts, Can we use some command from unix to find the available network interface? I did tried Its listing following, however how can I decide the which vender card is attached e.g. if its hme , bge or some thing else Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies

9. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies

10. Ubuntu

Error on network card

Hi Please can you help me to understand what could be wrong based on what I have captured in the logs: I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed. Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies
DH_INSTALLMODULES(1)						     Debhelper						      DH_INSTALLMODULES(1)

NAME
dh_installmodules - register kernel modules SYNOPSIS
dh_installmodules [debhelperoptions] [-n] [--name=name] DESCRIPTION
dh_installmodules is a debhelper program that is responsible for registering kernel modules. Kernel modules are searched for in the package build directory and if found, preinst, postinst and postrm commands are automatically generated to run depmod and register the modules when the package is installed. These commands are inserted into the maintainer scripts by dh_installdeb(1). FILES
debian/package.modprobe Installed to etc/modprobe.d/package.conf in the package build directory. OPTIONS
-n, --no-scripts Do not modify preinst/postinst/postrm scripts. --name=name When this parameter is used, dh_installmodules looks for and installs files named debian/package.name.modprobe instead of the usual debian/package.modprobe NOTES
Note that this command is not idempotent. dh_prep(1) should be called between invocations of this command. Otherwise, it may cause multiple instances of the same text to be added to maintainer scripts. SEE ALSO
debhelper(7) This program is a part of debhelper. AUTHOR
Joey Hess <joeyh@debian.org> 11.1.6ubuntu2 2018-05-10 DH_INSTALLMODULES(1)
All times are GMT -4. The time now is 07:16 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy