Sponsored Content
Full Discussion: Boot problem
Top Forums UNIX for Advanced & Expert Users Boot problem Post 13947 by nikk on Friday 25th of January 2002 09:59:35 AM
Old 01-25-2002
When you used cdrom for booting ,did you see your Boot Hard disk successfiully (via format command ).
If this hard has no physical & hardware problem , yes the only option is fresh installing again (but before that, analyse this mentioned hard disk for being sure of bad segment or sth like this,cause in future it will cause problem.


Rgrds,
nikk
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Dual Boot problem,help!!!!

I had Win98 and Win Xp on a dual boot on my system, I formatted my C: drive to get rid of Win98 and installed Linux Madrake in its Place, it all installed ok but when I boot up I can no longer dual boot and it goes straight into Mandrake Linux. How can I get either a dual boot so I can get to XP... (10 Replies)
Discussion started by: Merv
10 Replies

2. UNIX for Dummies Questions & Answers

linux boot problem

i have instaled a boot loader and win98 on drive c: and linux on drive d: and when i go to boot with the loader into linux nottin happens.is there some way i should install lilo to let it boot of a loader on drive c: ? (5 Replies)
Discussion started by: perleo
5 Replies

3. UNIX for Advanced & Expert Users

Boot Problem

Hi All. Yesterday my pc worked fine. Today when booting the sequence gets just past mounting the root filesystem - it then says ' Module dependencies up to date (no new kernel modules found).' At this point it hangs and goes no further! Does this sound familiar to anyone? I am running... (2 Replies)
Discussion started by: silvaman
2 Replies

4. Solaris

solaris boot problem boot error loading interpreter(misc/krtld)

When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error. cannot find mis/krtld boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies

5. AIX

Boot problem - 0c33

Hi Guys everyone know this problem on P595??? One of my servers, on boot, sleep 10-15 minute on led 0c33. I know that it's a console problem... but i don't understand how resolve it. Ideas??? P.S. Sorry for my english. Thanks. Zio (0 Replies)
Discussion started by: Zio Bill
0 Replies

6. Solaris

Boot problem

Hi everyone, I have sun fire280R machine before i it is installed with solaris5.9 now i want to upgrade it but it not booting from the cd rom ....OK prompt also not comming i dont have solaris keyboard to press stop-A key...i have a intel supported keyboard ...what may be the problem it is... (1 Reply)
Discussion started by: alakshmanrao
1 Replies

7. UNIX for Dummies Questions & Answers

boot problem

hello i have a sun server V890 and it stops booting after adding 2 CPUs modules and gives me the following error message: Enabling system bus....... Done Initializing CPUs......... Done Initializing boot memory.. RAM-Copy CRC failure!Can't start: No image found FATAL: Can't find/decompress... (0 Replies)
Discussion started by: bahjatm
0 Replies

8. Solaris

boot problem

hello i have a sun server V890 and it stops booting after adding 2 CPUs modules and gives me the following error message: Enabling system bus....... Done Initializing CPUs......... Done Initializing boot memory.. RAM-Copy CRC failure!Can't start: No image found FATAL: Can't find/decompress... (12 Replies)
Discussion started by: bahjatm
12 Replies

9. Solaris

Boot problem

Hi all, I have the the following SCSI diagnostic codes shown in the attached photo I suspect disk drive failure what can I do further to diagnose the disk. and if possible to boot into OS again. (5 Replies)
Discussion started by: h@foorsa.biz
5 Replies

10. Red Hat

Multipath boot problem

Hi, My HP machine is using as boot device a disk defined in the Storage (IBM V5000). The connection is done by fiber connected through fiber switch. No lacal disks are installed. I'm using redhat 6.6. I've installed and configured multipath. Everything seems to work properly, however,... (0 Replies)
Discussion started by: Pazzeo
0 Replies
hdio(7I)							  Ioctl Requests							  hdio(7I)

NAME
hdio - SMD and IPI disk control operations SYNOPSIS
#include <sys/hdio.h> DESCRIPTION
Note - The SMC and IPI drivers have been discontinued. dkio(7I) is now the preferred method for retrieving disk information. The SMD and IPI disk drivers supplied with this release support a set of ioctl(2) requests for diagnostics and bad sector information. Basic to these ioctl() requests are the definitions in <sys/hdio.h>. IOCTLS
HDKIOCGTYPE The argument is a pointer to a hdk_type structure (described below). This ioctl() gets specific information from the hard disk. HDKIOCSTYPE The argument is a pointer to a hdk_type structure (described below). This ioctl() sets specific information about the hard disk. /* * Used for drive info */ struct hdk_type { ushort_t hdkt_hsect; /* hard sector count (read only) */ ushort_t hdkt_promrev; /* prom revision (read only) */ uchar_t hdkt_drtype; /* drive type (ctlr specific) */ uchar_t hdkt_drstat; /* drive status (ctlr specific, ro) */ }; HDKIOCGBAD The argument is a pointer to a hdk_badmap structure (described below). This ioctl() is used to get the bad sector map from the disk. HDKIOCSBAD The argument is a pointer to a hdk_badmap structure (described below). This ioctl() is used to set the bad sector map on the disk. /* * Used for bad sector map */ struct hdk_badmap { caddr_t hdkb_bufaddr; /* address of user's map buffer */ }; HDKIOCGDIAG The argument is a pointer to a hdk_diag structure (described below). This ioctl() gets the most recent command that failed along with the sector and error number from the hard disk. /* * Used for disk diagnostics */ struct hdk_diag { ushort_t hdkd_errcmd; /* most recent command in error */ daddr_t hdkd_errsect; /* most recent sector in error */ uchar_t hdkd_errno; /* most recent error number */ uchar_t hdkd_severe; /* severity of most recent error */ }; SEE ALSO
ioctl(2), dkio(7I) SunOS 5.10 13 Aug 2002 hdio(7I)
All times are GMT -4. The time now is 07:39 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy