01-04-2002
If this is your default route then add the IP address of your default route to /etc/defaultrouter.
Or you can create a script to set it up (if you are going to be adding new routes all the time). Set it up in either /etc/rc2.d or /etc/rc3.d (Insure your Sxxnewroutes script runs after the networking scripts)
Example:
#!/sbin/sh
#
#
# Changes to interfaces and additional static routes
#
/usr/sbin/route add -net 172.26.0.0 172.16.26.2 2
/usr/sbin/route add -net 172.16.186 172.16.186.1 1
/usr/sbin/route add -net 172.16.1 172.16.186.1 1
/usr/sbin/route add -net 10.140 172.16.186.1 1
10 More Discussions You Might Find Interesting
1. Solaris
I am having problems getting this to work, though it seems like it would be simple. I have a host with 2 interfaces, hme0 (192.168.0.132) for the primary interface, and hme1 (192.168.0.16) for backups. I want it to talk to the backup host, which is 192.168.0.21, across the hme1 interface.
Thanks (2 Replies)
Discussion started by: 98_1LE
2 Replies
2. IP Networking
WE are running Unix - Solaris 2.6, we create a subnet. In the windows enviroment we are able to add a static route by using
route add -p 172.16.10.0 mask 255.255.255.0 172.16.17.224, but when we add the route in Solaris as
route add -net 172.16.10.0 255.255.255.0 172.16.17.224, we receive an... (5 Replies)
Discussion started by: cassy
5 Replies
3. Solaris
hi,
i installed solaris 9 on an SPARC server with two network interfaces. behind each interface is a small lan. i can reach every computer in every lan using one of the other interface when i am logged in the solaris. but if a computer from one lan has to connect to a computer on the other lan,... (4 Replies)
Discussion started by: bong02
4 Replies
4. Solaris
Hi,
Any one can help me in this below mentioned issue I am facing in my solaris server?
here the scenario goes....
i have multiple segments in my LAN like remote csr, database, production etc. and all the segments are configured in Windows/CISCo network.
from my all system in remote... (1 Reply)
Discussion started by: Praan
1 Replies
5. Solaris
Hi,
I am new to solaris 10. What is the procedure the os takes if a default route is not configured? I am using a multihomed server with 4 interfaces. It looked strange to me this morning, because i had not defined a default route it defaulted to making one up, with the ip address of another... (9 Replies)
Discussion started by: borderblaster
9 Replies
6. Solaris
Hi there,
I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add... (2 Replies)
Discussion started by: sreiniche
2 Replies
7. Solaris
Hey Guys.
I am trying include a route on the Sun Solaris 10 System an get the follow respond:
Network is unreachable.
Let me show the command.
root@ColectorDMSCNT # route add 200.44.46.0/27 161.196.84.193 1
add net 200.44.46.0/27: gateway 161.196.84.193: Network is unreachable
... (1 Reply)
Discussion started by: aggadtech08
1 Replies
8. Solaris
Hi,
Every time when i boot my system i have to manually issue the following commands.
ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up
route add default 192.168.200.1
I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies
9. Solaris
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
10. Solaris
Hi Solaris Experts,
I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node
# netstat -rnv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref
Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies
LEARN ABOUT NETBSD
route.conf
ROUTE.CONF(5) BSD File Formats Manual ROUTE.CONF(5)
NAME
route.conf -- static routes config file
DESCRIPTION
The route.conf file is read by the staticroute rc.d script during system start-up and shutdown, and is intended for adding and removing
static routes.
FILE FORMAT
Lines starting with a hash ('#') are comments and ignored. Lines starting with a plus sign ('+') are run during start-up, while lines start-
ing with a minus sign ('-') are run during system shutdown. If a line starts with a '!', the rest of the line will get evaluated as a shell
script fragment. All other lines are passed to route(8). During start-up, they are passed behind a ``route add -'' command and during shut-
down behind a ``route delete -'' command.
FILES
/etc/route.conf The route.conf file resides in /etc.
/etc/rc.d/staticroute
rc.d(8) script that parses route.conf.
EXAMPLES
In this example, the interface for the desired routing changes is set, the IP address on that interface is determined, and a route is added
during startup, or deleted during system shutdown.
# Set interface and determine current IP address for added route.
!ifname=bnx0
!ipaddr=$(/sbin/ifconfig ${ifname} | awk '$1 == "inet" {print $2}')
net 10.10.1 -interface ${ipaddr}
In this example, IP forwarding is turned on during start-up, and a static route added for 192.168.2.0. During system shutdown, the route is
removed and IP forwarding turned off.
# Turn on/off IP forwarding.
+sysctl -w net.inet.ip.forwarding=1
-sysctl -w net.inet.ip.forwarding=0
net 192.168.2.0 -netmask 255.255.255.0 192.168.150.2
SEE ALSO
rc.conf(5), rc(8), route(8)
BSD
May 1, 2012 BSD