01-04-2002
further help
When I look up ifconfig in the manual, it tells me that if I want to change any settings to edit the /etc/tcp file. When I go in to edit it, it just takes me to the next line, and everything I seem to type is not an editor command. Is there some way to actually show the file so I can see all the lines and freely edit them?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
How can I change the IP address and gateway info on a unix server? (2 Replies)
Discussion started by: gguzman
2 Replies
2. UNIX for Dummies Questions & Answers
How can I change the gateway address on my sco Openserver 5.0.6. A cisco firewall is recently installed but the gateway on the system is still pointing at the old one.
I want it to use the gateway address of the router.
Please help. Thanks (2 Replies)
Discussion started by: sshokunbi
2 Replies
3. SCO
I am trying to find out if you can create an ACL for telnet sessions and restrict it to a certain subnet/IP range..
any information or where to look would be greatly appreciated.
thanks (1 Reply)
Discussion started by: marvin51796
1 Replies
4. Shell Programming and Scripting
Hmmm, tough question for me, so I put it here.
I am trying to use shell script or mysql to do the following thing.
tableA, in which all are single ips.
sip
-------
1.2.3.4
8.8.8.8
123.3.32.1
....
and tableB, a list of our group subnets.
subnet
---------
1.0.0.0/8
20.0.1.0/24 (2 Replies)
Discussion started by: fedora
2 Replies
5. Programming
how we can get the gateway address.
i know gethostname used for ipaddress
how we can get the system gateway address.
thank u inadvance,
sree (2 Replies)
Discussion started by: phani_sree
2 Replies
6. IP Networking
Hi all,
I installed Fedora 9 + squid at one of PC at work.
Our company has windows 2003 servera acting as DHCP server.
During installation, i set linux box up as Static IP (192.168.0.100)
But once installation completed, The pc is assigned a different IP address instead of 192.168.0.100.... (3 Replies)
Discussion started by: c00kie88
3 Replies
7. IP Networking
Hi,
My project needs to migrate the existing Subnet (255.255.255.0) to a new subnet and change the ipaddresses (currently C class). How can I do that. I need some information.
John (0 Replies)
Discussion started by: johnmarsh
0 Replies
8. IP Networking
Is there a command that can lookup ip address, subnet mask, gateway, and dns all at the same. I know ifconfig can lookup ip address and subnet mask. I know route -n can lookup gateway. Not sure about a dns command. So I hope there is a way to lookup ip address, subnet mask, gateway, and dns all at... (2 Replies)
Discussion started by: cokedude
2 Replies
9. Shell Programming and Scripting
I have an input file:
class 1 3 5 10.10.10..0/23 hicks jimmy
class 3 10.12.10.0/22 mike
class.019283 10.10.15.10/20 henry
gym.847585 45 192.168.10.0/22 nancy jim steve maya
The output should look like this:
10.10.10..0/23
10.12.10.0/22
10.10.15.10/20
192.168.10.0/22
I have the... (3 Replies)
Discussion started by: e_mikey_2000
3 Replies
10. Shell Programming and Scripting
I have this subnet file shown below. How can I calculate all ip addresses from that list
103.22.200.0/22
141.101.64.0/18
10.0.0.0/22I need to be able to read the subnet file and print all IPs in those subnet to an out put file (3 Replies)
Discussion started by: e_mikey_2000
3 Replies
LEARN ABOUT DEBIAN
mkfs.bfs
MKFS.BFS(8) System Administration MKFS.BFS(8)
NAME
mkfs.bfs - make an SCO bfs filesystem
SYNOPSIS
mkfs.bfs [options] device [block-count]
DESCRIPTION
mkfs.bfs creates an SCO bfs filesystem on a block device (usually a disk partition or a file accessed via the loop device).
The block-count parameter is the desired size of the filesystem, in blocks. If nothing is specified, the entire partition will be used.
OPTIONS
-N, --inodes number
Specify the desired number of inodes (at most 512). If nothing is specified, some default number in the range 48-512 is picked
depending on the size of the partition.
-V, --vname label
Specify the volume label. I have no idea if/where this is used.
-F, --fname name
Specify the filesystem name. I have no idea if/where this is used.
-v, --verbose
Explain what is being done.
-c This option is silently ignored.
-l This option is silently ignored.
-h, --help
Display help text and exit.
-V, --version
Output version information and exit. Option -V only works as --version when it is the only option.
EXIT CODES
The exit code returned by mkfs.bfs is 0 when all went well, and 1 when something went wrong.
SEE ALSO
mkfs(8).
AVAILABILITY
The mkfs.bfs command is part of the util-linux package and is available from ftp://ftp.kernel.org/pub/linux/utils/util-linux/.
util-linux July 2011 MKFS.BFS(8)