11-28-2001
Port Usage
What is the command you use to check what ports are in use on a UNIX box.
Scott
9 More Discussions You Might Find Interesting
1. IP Networking
Can someone post a list about what usage of each port is, or tell me where I can find relative information? (2 Replies)
Discussion started by: HOUSCOUS
2 Replies
2. HP-UX
how can I find cpu usage memory usage swap usage and
I want to know CPU usage above X% and contiue Y times and memory usage above X % and contiue Y times
my final destination is monitor process
logical volume usage above X % and number of Logical voluage above
can I not to... (3 Replies)
Discussion started by: alert0919
3 Replies
3. Solaris
Hi,
I want to monitor the current cpu usage, monitor usage , disk I/o and network utlization for solaris using SNMP.
I want the oids for above tasks.
can you please tell me that
Thank you (2 Replies)
Discussion started by: S_venkatesh
2 Replies
4. Red Hat
are there linux commands or applications that i can use to find out what application was using a certain port at a certain time? there's teamquest,but it doesnt have this kind of information.
TIA. (2 Replies)
Discussion started by: bumblebee
2 Replies
5. AIX
How to monitor the IBM AIX server for I/O usage, memory usage, CPU usage, network usage, storage usage? (3 Replies)
Discussion started by: laknar
3 Replies
6. UNIX for Dummies Questions & Answers
Hi all,
Can you please tell me the command, with which one can know the amount of space a specific directory has used.
df -k . ---> Displays, the amount of space allocated, and used for a directory.
du -k <dir name> - gives me the memory used of all the files inside <dir>
But i... (2 Replies)
Discussion started by: abhisheksunkari
2 Replies
7. Solaris
I am trying to install Sun Java Web Server using an ordinary user with no root/sudo rights.
I need to allow this web server to use ports 80 and 443. How can this be done?:confused: (1 Reply)
Discussion started by: emealogistics
1 Replies
8. UNIX for Dummies Questions & Answers
Let's say i have 20 users logged on Server. How can I know how much memory percent used each of them is using with system time in each user? (2 Replies)
Discussion started by: roy1912
2 Replies
9. Solaris
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
dc(4) Kernel Interfaces Manual dc(4)
Name
dc - serial line/mouse/keyboard
Syntax
device dc0 at ibus? vector dcintr
Description
The serial line controller provides four ports, with modem control on two of the ports. The DECstation 3100 and DECstation 2100 only pro-
vide partial modem control. The DECstation 5000 provides full modem control. The ports are used as follows:
Port Usage
0 Graphics device keyboard at 4800 BPS
1 Mouse or tablet at 4800 BPS
2 Communications port 1 (w/modem control)/local terminal
3 Communications port 2 (w/modem control)/local terminal
Each communication port from the serial line controller behaves as described in and can be set to run at any of 16 speeds. For the encod-
ing, see
When a graphics device is not being used as the system console, communications port 2 becomes the system console. In this configuration,
the port can only be used at 9600 BPS and no modem control is supported.
The serial line driver operates in interrupt-per-character mode (all pending characters are flushed from the silo on each interrupt).
Restrictions
Speed must be set to 9600 BPS on the console port and 4800 BPS on ports used by graphics devices. The serial line driver enforces this
restriction; that is, changing speeds with the command may not always work on these ports.
Files
console terminal
local terminal
local terminal
See Also
console(4), devio(4), tty(4), ttys(5), MAKEDEV(8)
RISC dc(4)