03-09-2006
how to do live upgrade from solaris8 to 9 for sunfire 280R?
hi!!!!!!
how to upgrade sunfire 280R server from solaris8 to solaris9?
pls help me.
Thanks & Regards
-Vishal
10 More Discussions You Might Find Interesting
1. Solaris
hi,
i hv received SUNfire 280R system ........for its initial configuration i want to connect to it through hyperterminal from the windows system..........i hv got one serial port to RJ-45 port converter with the system............can anybody tell me the normal console cable which is used to... (3 Replies)
Discussion started by: girish_shukla
3 Replies
2. Solaris
Greetings all,
I'm in a bit of a situation. I have this Sunfire 280R system that did not have a floppy drive in it, yet we needed one. We grabbed one from another Sun box we had laying around unused, and installed it. The system couldnt recognize it. Tried another floppy drive (non-sun) and... (4 Replies)
Discussion started by: snackiesmores
4 Replies
3. Solaris
Hi there
Does anybody know what the biggest capacity disk I can get into a Sunfire 280R
I currently have two 73gb disks , but I need to get these up to the biggest available
Any help would be greatly appreciated (4 Replies)
Discussion started by: hcclnoodles
4 Replies
4. Solaris
Hi,
We had a disk go bad in this SunFire 280R, running Solaris 8 - Generic_117350-46. We replaced the disk and partitioned it. We metadetached all the metadevices but for some reason the new disk is showing up in the metadb as Concat/Stripe and it won't let us re-sync the mirror. We are not... (2 Replies)
Discussion started by: mgb
2 Replies
5. Solaris
Hi,
I have to question:
1) when O/S is booting, i see messages:
/dev/rdsk/c1t0d0s5: is logging
/dev/rdsk/c1t0d0s3: is logging
/dev/rdsk/c1t0d0s7: is logging
i partitioned these slices during installation of O/S 5.9. I can access to these mountpoint no problem. But... (3 Replies)
Discussion started by: lamoul
3 Replies
6. Solaris
hi,
i just completed installing O/S 5.9 on Sunfire 280R with O/S 5.9. During installation, i wasn't able to add IP, Default gateway, NDS and netmask because the lan port wasn't not active yet. Now that i have a lan port active, how to add network components onto the system?
I did ifconfig to... (1 Reply)
Discussion started by: lamoul
1 Replies
7. Solaris
Hi,
i just finished installing solaris 5.9 and I'm looking for the tools to tell me if i should update the patches or how to make sure that the current patches are ok?
thanks (2 Replies)
Discussion started by: lamoul
2 Replies
8. Solaris
Hi,
I' trying to install O/S 5.9 on Sparc system Sunfire 280R. I downloaded CD install and CD 2 from Sun Website but later i dowloaded CD 2 that i forgot for my installation. All CD are in ISO formats.
I boot system at OK prompt then issue
OK boot cdrom
when it asks for CD 1, i removed... (7 Replies)
Discussion started by: lamoul
7 Replies
9. Hardware
Hi,
I'm a newbie in the Unix world... :confused:
I own a Sun Sunfire 280R computer with one 750Mhz CPU. I ordered two CPU of 900Mhz to replace it; however in the Service manual from Sun I read that to use 900Mhz CPU i will need to have a OBP of at least version 4.5.16. When I type .version in... (2 Replies)
Discussion started by: Monkey114
2 Replies
10. Hardware
I got the system couple of days back from one of my friend. Last night I turned it on and I noticed that maintenance LED is on. At the same time I added an LCD monitor via VGA and nothing was showing on the screen. Though the system does not have any HDD So not sure if system will even show a BIOS... (3 Replies)
Discussion started by: pgirish007
3 Replies
LEARN ABOUT FREEBSD
dh_systemd_start
DH_SYSTEMD_START(1) Debhelper DH_SYSTEMD_START(1)
NAME
dh_systemd_start - start/stop/restart systemd unit files
SYNOPSIS
dh_systemd_start [debhelperoptions] [--restart-after-upgrade] [--no-stop-on-upgrade] [unitfile...]
DESCRIPTION
dh_systemd_start is a debhelper program that is responsible for starting/stopping or restarting systemd unit files in case no corresponding
sysv init script is available.
As with dh_installinit, the unit file is stopped before upgrades and started afterwards (unless --restart-after-upgrade is specified, in
which case it will only be restarted after the upgrade). This logic is not used when there is a corresponding SysV init script because
invoke-rc.d performs the stop/start/restart in that case.
OPTIONS
--restart-after-upgrade
Do not stop the unit file until after the package upgrade has been completed. This is the default behaviour in compat 10.
In earlier compat levels the default was to stop the unit file in the prerm, and start it again in the postinst.
This can be useful for daemons that should not have a possibly long downtime during upgrade. But you should make sure that the daemon
will not get confused by the package being upgraded while it's running before using this option.
--no-restart-after-upgrade
Undo a previous --restart-after-upgrade (or the default of compat 10). If no other options are given, this will cause the service to
be stopped in the prerm script and started again in the postinst script.
-r, --no-stop-on-upgrade, --no-restart-on-upgrade
Do not stop service on upgrade.
--no-start
Do not start the unit file after upgrades and after initial installation (the latter is only relevant for services without a
corresponding init script).
NOTES
Note that this command is not idempotent. dh_prep(1) should be called between invocations of this command (with the same arguments).
Otherwise, it may cause multiple instances of the same text to be added to maintainer scripts.
Note that dh_systemd_start should be run after dh_installinit so that it can detect corresponding SysV init scripts. The default sequence
in dh does the right thing, this note is only relevant when you are calling dh_systemd_start manually.
SEE ALSO
debhelper(7)
AUTHORS
pkg-systemd-maintainers@lists.alioth.debian.org
11.1.6ubuntu2 2018-05-10 DH_SYSTEMD_START(1)