Sponsored Content
Full Discussion: server reboot
Top Forums UNIX for Advanced & Expert Users server reboot Post 101357 by RTM on Tuesday 7th of March 2006 11:44:00 AM
Old 03-07-2006
Rebooting should send messages to your console - if you use some type of console connected to the system's serial port, then any logging would be found in that (example: my servers use conserver software - it logs anything going to the console in a log file set up via that software).

You can look at the man page for shutdown, boot, and init for info on the sequence - I didn't actually find anything that explains it (althought that may be due to the fact that there is no generic sequence since different servers boot up differently due to the hardware involved (E10K versus E4500 versus Netra).
 

9 More Discussions You Might Find Interesting

1. SCO

Reboot the sco server

Dear sir, I am using sco open server 5.06.How we can reboot the system without using root password? Whar are the permision need to change to do this. Thanks, Mostafizur Rahman (3 Replies)
Discussion started by: rahmanm
3 Replies

2. Shell Programming and Scripting

Server Reboot Alert

I want to get an email alert from a cronjob when a server got rebooted unexpectedly. Please help. Thanks! :confused: (2 Replies)
Discussion started by: angloi
2 Replies

3. AIX

IP setting changes after server reboot

I've recently changed my gateway setting using SMIT. Everything went fine except that the gateway setting kept reverting back to the old one everytime I reboot the server. I'm on AIX 5.2 running p-Series. Thanks for any info. (3 Replies)
Discussion started by: dereklow
3 Replies

4. Solaris

Reboot the server through console

Hi All, I want to know the procedure like if server is down, i want to reboot the server through console ($rsc or $sc prompt).Could you please help me out. I would really appreciate your cooperation. thanks for understanding regards krishna (5 Replies)
Discussion started by: murthy76
5 Replies

5. Solaris

Change gateway without reboot server

Hi Gurus Recently i had change the gateway for a server i had change the IP in the /etc/defaultrouter and run the below command # route add default 10.86.33.222 # route delete default 10.86.33.1 # netstat -rn Routing Table: IPv4 Destination Gateway Flags Ref ... (2 Replies)
Discussion started by: SmartAntz
2 Replies

6. Solaris

Zones not booting after server reboot

Hello guys This is my first post. I have very little experience and I woud appreciate your input on this problem. I have a server running Solaris 10. In that server I have 2 zones that work perfectly fine, however, if I reboot the server, the zones don't boot and I have to do it manually. i... (12 Replies)
Discussion started by: designbc
12 Replies

7. Linux

Linux server reboot

We reboot our linux servers daily. Is it needed ? (10 Replies)
Discussion started by: linuxadmin
10 Replies

8. Solaris

Validate mountpoints on solaris server after server reboot

Hi, anyone please let us know how to write shell script to find the missing mountpoints after server reboot. i want to take the mountpount information before server reboot, and validate the mountpoints after server reboot if any missing.please let us know the shell script from begining to end as... (24 Replies)
Discussion started by: VenkatReddy786
24 Replies

9. Red Hat

Server reboot

Hi, The server got rebooted and below messages can be seen in /var/log/messages Sep 7 10:49:12 minersville kernel: Call Trace: <IRQ> <ffffffff80167420>{__alloc_pages+796} Sep 7 10:49:12 minersville kernel: <ffffffff80182814>{kmem_getpages+106} <ffffffff80183c16>{fallback_alloc+304}... (3 Replies)
Discussion started by: admin_db
3 Replies
cvc(7D) 							      Devices								   cvc(7D)

NAME
cvc - virtual console driver DESCRIPTION
The cvc virtual console driver is a STREAMS-based pseudo driver that supports the network console. The cvc driver interfaces with con- sole(7D). Logically, the cvc driver sits below the console driver. It redirects console output to the cvcredir(7D) driver if a network console con- nection is active. If a network console connection is not active, it redirects console output to an internal hardware interface. The cvc driver receives console input from cvcredir and internal hardware and passes it to the process associated with /dev/console. NOTES
The cvc facility supersedes the SunOS wscons(7D) facility, which should not be used in conjunction with cvc. The wscons driver is use- ful for systems with directly attached consoles (frame buffers and keyboards), but is not useful with platforms using cvc, which have no local keyboard or frame buffer. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +--------------------+--------------------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +--------------------+--------------------------------------+ |Architecture |Sun Enterprise 10000 servers, Sun | | |Fire 15000 servers | +--------------------+--------------------------------------+ |Availability |SUNWcvc.u | +--------------------+--------------------------------------+ SEE ALSO
cvcd(1M), attributes(5), console(7D), cvcredir(7D), wscons(7D) Sun Enterprise 10000 SSP Reference Manual Sun System Management Services (SMS) Reference Manual SunOS 5.11 15 Sep 2000 cvc(7D)
All times are GMT -4. The time now is 01:11 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy