How can I tell which network card is which?

10 More Discussions You Might Find Interesting

1. Ubuntu

Error on network card

Hi Please can you help me to understand what could be wrong based on what I have captured in the logs: I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed. Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4...

2. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101...

3. Solaris

Network Card Name details

Hi All, Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ? This is such a basic question which i always overlooked :( Thanks !

4. UNIX for Dummies Questions & Answers

How to install a network card

Hey guys, Sorry, this question might look stupid but I have no idea how to install a network card. My server is a Dell PowerEdge T105 with Debian 5.0 Lenny. My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express. I've plugged the card innside my server and I can see...

5. Solaris

How to identifying the network card ?

Hi Experts, Can we use some command from unix to find the available network interface? I did tried Its listing following, however how can I decide the which vender card is attached e.g. if its hme , bge or some thing else Thanks

6. UNIX for Dummies Questions & Answers

Network card and internet

Hi!. I have problems installing my network card under ther redhat kernel. First i tryed my integrated intel pro set 10/100 then my d-link 530tx Pci but none of them seems to be found. also i huse my network card to connect to the net trough PPPOE where i need to type my username and...

7. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of...

8. IP Networking

Network Card with SGI

The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out > link ok < when i connected > But...

9. UNIX for Dummies Questions & Answers

Installing network card

1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface, 2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out.

10. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the...

LEARN ABOUT REDHAT

axnet_cs

AXNET_CS(4)						     Kernel Interfaces Manual						       AXNET_CS(4)

NAME

       axnet_cs - Asix AX88190 chipset PCMCIA Ethernet Driver

SYNOPSIS

       insmod axnet_cs.o [pc_debug=n] [irq_list=i,j,...]

DESCRIPTION

       Axnet_cs  is  a driver for PCMCIA ethernet cards based on the Asix AX88190 chipset.  These cards are mostly NE2000 compatible but have sev-
       eral bugs that are sufficiently tricky to work around that a separate driver was deemed necessary.  When this driver is bound to a card, it
       allocates  the  next  available	ethernet  device (eth0..eth#).	This device name will be reported in the kernel log file, and passed on to
       cardmgr(8).

PARAMETERS

       pc_debug=n
	      Selects the PCMCIA debugging level.  This parameter is only available if the module is compiled with debugging enabled.  A  non-zero
	      value enables debugging.

       irq_list=i,j,...
	      Specifies the set of interrupts that may be allocated by this driver.

DIAGNOSTICS

       axnet_cs: this is not an AX88190 card!
	      Indicates that this card is probably a normal NE2000 compatible card, which requires the pcnet_cs driver.

       eth#: interrupt(s) dropped!
	      Indicates that the driver did not receive an interrupt notification for some reason.  The driver will poll the card (with a signifi-
	      cant performance penalty) if the problem persists.  The most likely cause is an interrupt conflict and/or host bridge  configuration
	      problem.

AUTHOR

       David Hinds - dahinds@users.sourceforge.net

SEE ALSO

       cardmgr(8), pcmcia(5).

pcmcia-cs							2001/08/17 12:51:58						       AXNET_CS(4)

UNIX for Dummies Questions & Answers