9 More Discussions You Might Find Interesting
1. AIX
Been trying to get a directory NFS-mounted with no success. I've tried both NFS v3 and v4, but currently trying v4. I can't figure out what's going on here.
server: sbkovwadmd01
sbkovwadmd01# chnfsdom
Current local domain: edw.dev
sbkovwadmd01# lssrc -a | grep nfs | grep active
nfsd ... (3 Replies)
Discussion started by: eckertd
3 Replies
2. UNIX for Advanced & Expert Users
hi all
i have hp proliant ml350 g6 , i want install unixware 7.1.4 ,
i excute steps installation but an error ocured hard disk not found after completed install HBA DRIVER , when chnage using DCU utility from automatic to mannul some reseason like unkow device see must be configure
can you help... (1 Reply)
Discussion started by: eng.sami80
1 Replies
3. Red Hat
Dear All ,
One of our Oracle Database Server , which got hanged a couple of days before , so that we could not login to the Server , but it was pinging.
So we tried various options and at last we did a reboot of this server.
To find out the root cause of the Server Hang , when i checked the... (2 Replies)
Discussion started by: jegaraman
2 Replies
4. Red Hat
Hello Folks,
when i run simple ls command i am getting the output properly. See below:
# ls
ecapPlat.err FileMover.log.2 FileScrubber.log.1 MeasServer.log mysentfile surv.log
ecapPlat.log FileMover.log.3 FileScrubber.log.2 MeasServer.log.1 netConfig.err TimeServer.log
FileMover.log... (1 Reply)
Discussion started by: manuswami
1 Replies
5. SCO
Hi, I'm new to this Unix world and have taken over looking after the I.T side of things at work, which includes the internal ERP system which runs on a UNIX SCO platform.
My initial worry is what state this is in as its been on site over 20 years.
What would be the first things to check on... (13 Replies)
Discussion started by: Mick_Dundee
13 Replies
6. Red Hat
Hello everybody..
I have RHEL-4 Server with kernel - Linux 2.6.9-78.0.1.ELlargesmp x86_64
It is used for Development usage..
That server got hang and so reboot was required, when checked log file i found following messages,
kernel: warning: many lost ticks.
kernel: Your time source... (4 Replies)
Discussion started by: laxmikant
4 Replies
7. Solaris
Guys,
I am having difficulties in bringing my server to OBP. The server hung infinitely after issuing init 0 command. I have already stopped all the applications running but to no avail. :confused:
Has anyone encountered this problem before? Appreciate if you could shed some lights.
... (4 Replies)
Discussion started by: honmin
4 Replies
8. SCO
Hello,
I am having performance problem when , i ported a c code from Unixware 2.1 to Unixware 7.0.0.
My program establishes a synchornous connection with the client in a windows OS and then sends and receives messsages using the recv and send calls.
What i hyave noticed is that after a... (0 Replies)
Discussion started by: Amith
0 Replies
9. UNIX for Dummies Questions & Answers
All greetings:)
I had problem: hangs linux a server, and hangs always on miscellaneous and at various times, for example, can stand about one week, and can and in some minutes after reboot. Tried on a server to put windows 2003, with him problems do not arise. What could it be?:)
I from... (4 Replies)
Discussion started by: SDaniel
4 Replies
ccr(8) System Manager's Manual ccr(8)
Name
ccr - remote console carrier requester
Syntax
ccr [ options ] node
Description
The command establishes a logical connection between your ULTRIX system and the console carrier server on a remote system. enables your
terminal to act as the console for a remote unattended system. For example, your terminal can act as the console for a Digital Ethernet
Communications Server (DECSA) and its resident software. The node is the name or address of the target node. A node name consists of from
one to six alphanumeric characters. A node address consist of two decimal integers (n.n), where the first indicates the network number
(1-63), and the second indicates the node address (1-1023).
You can use to force a crash if a server node becomes unresponsive. To determine how to force a crash, see the documentation for the
respective server product.
The requirements for using are as follows:
o The host node (that is, your local ULTRIX node) and the remote node must be on the same Ethernet.
o If your server product is a DECSA, the console carrier server image (plutocc.sys) and its loader file (plutowl.sys) must be located in
on your ULTRIX node. The pluocc.sys and plutowl.sys files are not need, nor is any loading done for other servers. For more details,
see the installation guide for the particular server product.
<CTRL/D> exits from console carrier mode and terminates
Options
-c Uses the specified circuit to connect to the target node.
-h Uses the specified address (next argument) as the Ethernet address of the target node.
-n Uses the next argument as the target node ID.
-p Uses the specified service password (next arguments) in accessing the target node.
Examples
# /etc/ccr -c qna-0 -n dallas <RET>
ccr: Remote console reserved
.
.
.
<CTRL/D>
ccr: Remote console released
#
Restrictions
You must have superuser privileges to run
Diagnostics
The command can return the following diagnostic messages:
ccr: Remote console reserved
The command has successfully connected to the remote console server and your terminal is now capable of acting as a console for the remote
node.
ccr: Remote console released
Your connection with the remote console server has been terminated and you are no longer in console carrier mode.
ccr: Remote console already in use
The remote console server that you are attempting to connect to is already reserved by another user.
ccr: Permission denied
You do not have the necessary privileges to run (You must be a superuser.)
ccr: Hardware address required
The command is unable to locate the hardware address of the remote node to which you are attempting to connect. A remote node's hardware
address must be defined either in the command line, or in its nodes database entry. (Nodes database entries are defined with the command.)
ccr: No node entry in database
The command does not recognize the remote node to which you are attempting to connect, since the node-id that you specified is not defined
in the nodes database. (Nodes database entries are defined with the command.)
Files
Console carrier server image
Console carrier server loader
See Also
addnode(8), getnode(8), load(8), remnode(8), trigger(8)
Guide to Local Transport Servers
ccr(8)