9 More Discussions You Might Find Interesting
1. Solaris
Hello dears
how to assign IPv4 and IPv6 addresses with same interface on solaris 10 (1 Reply)
Discussion started by: ttashman
1 Replies
2. AIX
Hi all,
I have setup ipv6 in AIX machine using autoconf6 command.
I was successfull in doing this. after execution of the command local link address was assigned to one of the interfaces
(en1).But I have to setup the following environment as well.
1) Machine with only IPv6 support(IPv4... (0 Replies)
Discussion started by: ard
0 Replies
3. Solaris
Hi
I am looking to set-up ISC DHCP to support ipv6, and to migrate my existing SUN DHCP ipv4 to ISC,
finding the ipv4 options for the SUN DHCP options was ok eg
TFTPsrvN = tftp-server-name
OptBootF = bootfile-name
However if I set up a DHCPv6 does anyone know what the equivalent... (1 Reply)
Discussion started by: eeisken
1 Replies
4. Solaris
Hi
I am looking to have an NTP server that will support both ipv4 and ipv6 clients. Is there anything specific about the configuration that I should be looking at? (7 Replies)
Discussion started by: eeisken
7 Replies
5. Red Hat
Hello,
I was wondering if it would be possible to run two VMs one with services for IPv4 and the other one with services for IPv6. The main physical system would be connected to a IPv6 switch.
I think it should be fine but I would like to hear out your comments. (1 Reply)
Discussion started by: svalenciatech
1 Replies
6. Shell Programming and Scripting
I have perl script that I use to check and ping a list of ip,
The problem is, I didnt understand how to ping ipv6 on perl,
Could I use Ping::External??And how could I get the ping result (reply or not)?
This is my code
#!/usr/bin/perl --
use Net::Ping;
use Data::Validate::IP;
use... (3 Replies)
Discussion started by: franzramadhan
3 Replies
7. Solaris
Hi folks, i hope you'll help me to configure my ipv6 tunnel.
First, i create my tunnel in:
Hurricane Electric Free IPv6 Tunnel Broker
My IP is 83.228.93.34
in HE:
------------------------
Server IPv4 address: 216.66.84.46
Server IPv6 address: 2001:470:1f14:16a::1/64
Client IPv4 address: ... (2 Replies)
Discussion started by: static
2 Replies
8. AIX
hello
i'm working on AIX 5300-05-03 P520 hacmp 5.4
when connection to the internet is going down , firewall down, my application work verey verey slowly!!! and on the sliffer output i'm got trys of my serevr to do convert from ipv4 ipv6 ( 0.0.2.0 and AAAAAAAA).
some one have an idea why... (1 Reply)
Discussion started by: ariec
1 Replies
9. UNIX for Advanced & Expert Users
hello
i'm working on aix 5300-05-03 hacmp ver 5.4
well my issue is that when firewall (gateway to internet ) goes down my machine start to work very very slowly!!!
the output of the sniffer is that on the output card , my machine try to convert ipv4 to ipv6 0.0.2.0
my machine is not configure... (1 Reply)
Discussion started by: ariec
1 Replies
pppoesd.conf(4) Kernel Interfaces Manual pppoesd.conf(4)
NAME
pppoesd.conf - PPPoE (Point to Point Protocol over Ethernet) server configuration file
DESCRIPTION
is the configuration file for the daemon. This file is read by to initialize the server. The default file is You can use this file to set
parameters for each network interface used by during PPPoE sessions. Each entry in the file is of the following format:
Each entry in the configuration file is separated by a blank line. Blank lines and lines that begin with are ignored.
Parameters
contains the following parameters:
Specify the name of the service that the server can offer to the client.
A value of implies that the server is ready to offer any service to the client.
Specify the name of the access concentrator from which you wish to make
services available.
Specify a tag used by the client to uniquely associate an access
concentrator's response (PADO or PADS) to a particular client request (PADI or PADR).
Specify the number of times
tries to retransmit either a PADI or PADR packet when an access concentrator does not respond to the client's request.
Specify the timeout value in seconds.
waits for this duration to receive either a PADO or PADS packet before retransmitting a PADI/PADR packet. The default
value is 15 seconds.
Specify the command-line options of
See pppd(1) for more information.
Sample pppoesd.conf File
[ lan4 ]
service=any
acname=gatt3
ac_cookie=1
#host_unique=0
timeout=1200
#retry-number=3
local-ipv4-address=1.2.3.4
ipv4-address-pool=5.6.7.8 - 5.6.7.101
pppd-options=mru 1492 debug 11
# Following entries are related to PPPoEv6
local-ipv6-identifier=::9
ipv6-identifier-pool=::10 - ::100
AUTHOR
was developed by Hewlett-Packard.
FILES
PPPoE server daemon
PPPoE relay
PPPoE client
PPP daemon
SEE ALSO
pppd(1), pppoec(1), pppoerd(1M), pppoesd(1M).
pppoesd.conf(4)