nxge: [ID 339653 kern.notice] NOTICE: nxge0: xcvr addr:0x0d - link is down
nxge: [ID 339653 kern.notice] NOTICE: nxge1: xcvr addr:0x0c - link is down
nxge: [ID 339653 kern.notice] NOTICE: nxge2: xcvr addr:0x0b - link is down
nxge: [ID 339653 kern.notice] NOTICE: nxge3: xcvr addr:0x0a - link is down
Why these messages are coming repeatedly. These interfaces are not using.
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Im getting stumped on one of my unix problems. Im a college student taking unix and for one of my assignments I am to write a few programs. I done the programs but on one of them I have to modify it by using sed instead of a while do loop. here's the while loop
while
do
... (2 Replies)
Pls can u help me diagnosed this Notice l receive during booting of my openserver 5.0.4 unix from the kernel.
NOTICE:cha:SCSI bus has been reset ha=0
Attached SCSI peripherals will retunr to power up
state (ChaN04)
NOTICE:cha:SCSI command timed out ha=0... (2 Replies)
Discussion started by: kayode
2 Replies
7. Post Here to Contact Site Administrators and Moderators
syslog.conf(4) Kernel Interfaces Manual syslog.conf(4)NAME
syslog.conf - syslogd configuration file
SYNOPSIS
facility.severity destination Where: Is part of the system generating the message, specified in /usr/include/sys/syslog_pri.h.
See also the syslogd(8) reference page. The severity level, which can be emerg, alert, crit, err, warning, notice, info, or debug. See
/usr/include/sys/syslog_pri.h.
The syslogd daemon logs all messages of the specified severity level plus all messages of greater severity. For example, if you
specify level err, all messages of levels err, crit, alert, and emerg or panic are logged. A local file pathname to a log file, a
host name for remote logging or a list of users. In the latter case the users will receive messages when they are logged in. An
asterisk (*) causes a message to be sent to all users who are currently logged in.
DESCRIPTION
The /etc/syslog.conf file is a system file that enables you to configure or filter events that are to be logged by syslogd. You can specify
more than one facility and its severity level by separating them with semicolons.
You can specify more than one facility logs to the same file by separating the facilities with commas, as shown in the EXAMPLES section.
The syslogd daemon ignores blank lines and lines that begin with an octothorpe (#). You can specify # as the first character in a line to
include comments in the file or to disable an entry. The facility and severity level are separated from the destination by one or more tab
characters.
If you want the syslogd daemon to use a configuration file other than the default, you must specify the file name with the following com-
mand: # syslogd -f config_file
Daily Log Files
You can specify in the /etc/syslog.conf file that the syslogd daemon create daily log files. To create daily log files, use the following
syntax to specify the path name of the message destination: /var/adm/syslog.dated/ { file} The file variable specifies the name of the log
file, for example, mail.log or kern.log. If you specify a /var/adm/syslog.dated/file path name destination, each day the syslogd daemon
creates a sub-directory under the /var/adm/syslog.dated directory and a log file in the sub-directory, using the following syntax:
/var/adm/syslog.dated/ date / file Where: The date variable specifies the day, month, and time that the log file was created. The file
variable specifies the name of the log file you previously specified in the /etc/syslog.conf file. The syslogd daemon automatically cre-
ates a new date directory every 24 hours and also when you boot the system. The current directory is a link to the latest date directory.
To get the latest logs, you only need to reference the /var/adm/syslog.dated/current directory.
EXAMPLES
The following is a sample /etc/syslog.conf file: # # syslogd config file # # facilities: kern user mail daemon auth syslog lpr binary #
priorities: emerg alert crit err warning notice info debug # kern.debug /var/adm/syslog.dated/kern.log user.debug /var/adm/sys-
log.dated/user.log daemon.debug /var/adm/syslog.dated/daemon.log auth.crit;syslog.debug /var/adm/syslog.dated/syslog.log mail,lpr.debug
/var/adm/syslog.dated/misc.log msgbuf.err /var/adm/crash.dated/msgbuf.savecore kern.debug /var/adm/messages kern.debug /dev/console *.emerg
*
FILES
/etc/syslog.conf
/etc/syslog.auth - Authorization file for remote logging.
/usr/include/sys/syslog_pri.h - Common components of a syslog event log record.
RELATED INFORMATION
Commands: /usr/sbin/syslogd(8), /usr/sbin/binlogd(8)
System Administration delim off
syslog.conf(4)