10 More Discussions You Might Find Interesting
1. Hardware
Can you mix DIMMs in a T6320 (sparc) blade? I have read/heard that the DIMMs in a memory bay must be identical but can you have different size DIMMs installed in the blade?
For instance, can you have 1 4GB DIMM in bay 0, 2 2GB DIMMs in bay 1, 4 1 GB DIMMs in bay 2 and 2 2GB DIMMs in bay 3 for a... (0 Replies)
Discussion started by: bluescreen
0 Replies
2. Solaris
Hi, I can't seem to get Graphs using Report Manager for Memory and Hard Disk. Only CPU is working fine. Following are some screen shots:
- Sun Management Center 4.0
http://img689.imageshack.us/img689/7555/smcu.jpg
- Performance Report
http://img25.imageshack.us/img25/3015/reportdo.jpg
By... (2 Replies)
Discussion started by: Mack1982
2 Replies
3. Solaris
Hi folks, can you please help to print cpu and memory configuration on sun host. (4 Replies)
Discussion started by: ggolub
4 Replies
4. Solaris
Hi,
I recently acquired an old Sun Fire v120 from work. I plan to play around with this at home whilst I'm studying for my SCSA exams. Only problem is it currently has no memory installed. I believe the memory modules required are 168 pin PC133 DIMMs. Unfortunately, the original Sun modules are... (3 Replies)
Discussion started by: skinyana
3 Replies
5. Solaris
Hi, this is my 1st post here, I don't know is it proper or not for the question I have, but I may try ask anyway, since it is question about sun's hw/sw issue...
I have my blade 1000 installed additional memory kits, it was originally 2G memory installed on Group0(Bank 0/2) Dimm slots, I got... (5 Replies)
Discussion started by: netshu
5 Replies
6. Solaris
Hi, I've been a member for a while but have never posted. I have a Sun Blade 100 desktop and I just installed Solaris 10 and it is unbearably slow. I only have 128 Meg of RAM and need to upgrade. I have searched and found many online resources that have RAM, but I was wondering if anyone has... (12 Replies)
Discussion started by: BrewDudeBob
12 Replies
7. Solaris
Hi
I am facing a problem with memory in SunOS 5.9. I just want to check the memory usage. Can anybody suggest me a command that will help me in this regard. (4 Replies)
Discussion started by: rajarsi.ghosh
4 Replies
8. Programming
Hi, I try to marshal a unsigned int and a char * into a buffer, and then unmarshal them later to get them out. I need to put the char * in the front and unsigned int at the end of the buffer. However, my system always give me "BUS ERROR". I am using Sun Sparcs Sloris 2.10.
My code to marshal... (6 Replies)
Discussion started by: nj302
6 Replies
9. Solaris
Hi, I try to marshal a unsigned int and a char * into a buffer, and then unmarshal them later to get them out. I need to put the char * in the front and unsigned int at the end of the buffer. However, my system always give me "BUS ERROR". I am using Sun Sparcs Sloris 2.10.
My code to marshal the... (1 Reply)
Discussion started by: nj302
1 Replies
10. UNIX for Dummies Questions & Answers
I would like to upgrade the memory in my Sun Blade 150 workstation. In reading through Sun's Blade 150 DIMM Installation Guide, it indicates that the memory must be "certified by Sun for the Sun Blade 150 system."
Does anyone know if any SDRAM, PC133 • CL=2 • Unbuffered • ECC • 133MHz • 3.3V ... (2 Replies)
Discussion started by: here2learn
2 Replies
STRUCT
STATION_INFO(9) Actions and configuration STRUCT STATION_INFO(9)
NAME
struct_station_info - station information
SYNOPSIS
struct station_info {
u32 filled;
u32 connected_time;
u32 inactive_time;
u64 rx_bytes;
u64 tx_bytes;
u16 llid;
u16 plid;
u8 plink_state;
s8 signal;
s8 signal_avg;
struct rate_info txrate;
struct rate_info rxrate;
u32 rx_packets;
u32 tx_packets;
u32 tx_retries;
u32 tx_failed;
u32 rx_dropped_misc;
struct sta_bss_parameters bss_param;
struct nl80211_sta_flag_update sta_flags;
int generation;
const u8 * assoc_req_ies;
size_t assoc_req_ies_len;
u32 beacon_loss_count;
s64 t_offset;
enum nl80211_mesh_power_mode local_pm;
enum nl80211_mesh_power_mode peer_pm;
enum nl80211_mesh_power_mode nonpeer_pm;
};
MEMBERS
filled
bitflag of flags from enum station_info_flags
connected_time
time(in secs) since a station is last connected
inactive_time
time since last station activity (tx/rx) in milliseconds
rx_bytes
bytes received from this station
tx_bytes
bytes transmitted to this station
llid
mesh local link id
plid
mesh peer link id
plink_state
mesh peer link state
signal
The signal strength, type depends on the wiphy's signal_type. For CFG80211_SIGNAL_TYPE_MBM, value is expressed in _dBm_.
signal_avg
Average signal strength, type depends on the wiphy's signal_type. For CFG80211_SIGNAL_TYPE_MBM, value is expressed in _dBm_.
txrate
current unicast bitrate from this station
rxrate
current unicast bitrate to this station
rx_packets
packets received from this station
tx_packets
packets transmitted to this station
tx_retries
cumulative retry counts
tx_failed
number of failed transmissions (retries exceeded, no ACK)
rx_dropped_misc
Dropped for un-specified reason.
bss_param
current BSS parameters
sta_flags
station flags mask & values
generation
generation number for nl80211 dumps. This number should increase every time the list of stations changes, i.e. when a station is added
or removed, so that userspace can tell whether it got a consistent snapshot.
assoc_req_ies
IEs from (Re)Association Request. This is used only when in AP mode with drivers that do not use user space MLME/SME implementation.
The information is provided for the cfg80211_new_sta calls to notify user space of the IEs.
assoc_req_ies_len
Length of assoc_req_ies buffer in octets.
beacon_loss_count
Number of times beacon loss event has triggered.
t_offset
Time offset of the station relative to this host.
local_pm
local mesh STA power save mode
peer_pm
peer mesh STA power save mode
nonpeer_pm
non-peer mesh STA power save mode
DESCRIPTION
Station information filled by driver for get_station and dump_station.
AUTHOR
Johannes Berg <johannes@sipsolutions.net>
Author.
COPYRIGHT
Kernel Hackers Manual 3.10 June 2014 STRUCT STATION_INFO(9)
