10 More Discussions You Might Find Interesting
1. Red Hat
Hi,
I have two ntp servers in my cluster and I want all the nodes in my cluster to sync with either of the ntp servers or just one. Unfortunately it keep rotating the sync, between my ntp server 1, ntp server 2 and local. Is there anyway I can change the sync to avoid local?
# ntpq -p
... (3 Replies)
Discussion started by: pjeedu2247
3 Replies
2. Red Hat
Hi,
Could you please explain about "restrict" parameters in /etc/ntp.conf in ntp client and ntp Servers.
Example:
restrict 127.0.0.1
restrict -6 ::1
restrict 192.168.1.0 mask 255.255.255.0 nomodify notrap
Regards,
Mastan (1 Reply)
Discussion started by: mastansaheb
1 Replies
3. Solaris
hi all
ntp client side configuration file is done but in
# ntpq -p
remote refid st t when poll reach delay offset disp
==============================================================================
ntpserver .INIT. 16 u - 64 0 0.00 0.000... (5 Replies)
Discussion started by: nikhil kasar
5 Replies
4. HP-UX
Hi
I wonder if its possible to setup NTP clients running HP-UX o.s. from a solaris 10 NTP server?
FR (3 Replies)
Discussion started by: fretagi
3 Replies
5. UNIX for Dummies Questions & Answers
hello Guys,
I have an NTP problem on my SUN N240 server. External NTP server is being used for this box and when i run 'ntpq -p' i get connection refused message;
ntpq -p
ntpq: read: Connection refused
Here this is the ntp.conf file:
cat /etc/ntp.conf
# BEGIN NTP SERVERS
server... (6 Replies)
Discussion started by: dyavuzy1
6 Replies
6. Linux
All here, thank you for listening. Now I've set up a Linux NTP server by adding a external windows NTP server in /etc/ntp.conf. Then I start the ntpd daemon. But how often does the Linux NTP server update its time with the external NTP server? I've looked up everywhere but found no information... (1 Reply)
Discussion started by: MichaelLi
1 Replies
7. Red Hat
Hi,
I'm trying to configure NTP client, however it failes to sync correctly.
Even after I manually set the time, once it connects with the NTP server, it pushes the time ahead by 4 hours.
We have set an AIX host as NTP server. It works fine for other AIX hosts, however fails on RHEL 5.4
... (4 Replies)
Discussion started by: max_min
4 Replies
8. Solaris
All,
How do you set a Solaris 9 server which received ntp updates from a ntp server to broadcast them on a local subnet. I have created a /etc/inet/ntp.conf file to receive the updates from a server on network and need to make this server become like a ntp relay from the main server.
Any... (1 Reply)
Discussion started by: bubba112557
1 Replies
9. UNIX for Dummies Questions & Answers
Hi all,
I'm sure this question was asked before but I couldn't find what I was looking for in the 2 threads I found on here.
Here's my question/problem:
I have an isolated (no connection to outside world at all) Unix network. I want to have time sync between my other non-PC based system... (0 Replies)
Discussion started by: mariobernier
0 Replies
10. UNIX for Advanced & Expert Users
Hi.
i was wondering if anyone can show me or direct me on setting up a ntp server under redhat.. Is there any howtos so i can get familar to it "any good sites" (3 Replies)
Discussion started by: souldier
3 Replies
ntptrace(1) General Commands Manual ntptrace(1)
NAME
ntptrace - trace a chain of NTP servers back to the primary source
SYNOPSIS
ntptrace [ -vdn ] [ -r retries ] [ -t timeout ] [ server ]
DESCRIPTION
ntptrace determines where a given Network Time Protocol (NTP) server gets its time from, and follows the chain of NTP servers back to
their master time source. If given no arguments, it starts with localhost . Here is an example of the output from ntptrace :
% ntptrace localhost: stratum 4, offset 0.0019529, synch distance 0.144135 server2ozo.com: stratum 2, offset 0.0124263, synch distance
0.115784 usndh.edu: stratum 1, offset 0.0019298, synch distance 0.011993, refid On each line, the fields are (left to right): the host
name, the host stratum, the time offset between that host and the local host (as measured by ntptrace ; this is why it is not always zero
for " localhost "), the host synchronization distance, and (only for stratum-1 servers) the reference clock ID. All times are given in sec-
onds. Note that the stratum is the server hop count to the primary source, while the synchronization distance is the estimated error rela-
tive to the primary source. These terms are precisely defined in RFC-1305.
OPTIONS
-d Turns on some debugging output.
-n Turns off the printing of host names; instead, host IP addresses are given. This may be useful if a nameserver is down.
-r retries Sets the number of retransmission attempts for each host (default = 5).
-t timeout Sets the retransmission timeout (in seconds) (default = 2).
-v Prints verbose information about the NTP servers.
BUGS
This program makes no attempt to improve accuracy by doing multiple samples.
SEE ALSO
More documentation is available in the package ntp-doc.
AUTHOR
David L. Mills <mills@udel.edu>
ntp 4.1.1b-r5 ntptrace(1)