10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
We have 2 different servers say A and B and I want to check the log file of 2 servers simultaneously.
If I am logged into server A how can I connect to server B.
I have used ssh username@B.But it is asking password. How can I give the password on ssh.
Or is there any other utility for... (2 Replies)
Discussion started by: jim john
2 Replies
2. IP Networking
I want to know potential problems with the following scenario OR if it is an ok way to have my network setup:
I have 2 WAN connections to the internet. I have each WAN connection plugged into its own router. Router DD-WRT is gateway for servers (192.0.10.50). Router Tomato is gateway for pc's... (1 Reply)
Discussion started by: herot
1 Replies
3. Linux
Well im on Fedora, and theres no sub section for Fedora so yea
Well how do you connect to an SSH, while on a windows terminal?
And also to transfer a file from my desktop to a server?
how is this done
scp command is not working for me (3 Replies)
Discussion started by: gangsta
3 Replies
4. Shell Programming and Scripting
Hey guys,
I just started college a few days ago. To my dismay, my school has a very frustrating wireless network access system. Every time you want to use the network, you need to open up a browser and get re-directed to a login page. Every access, you need to reenter the same username and... (1 Reply)
Discussion started by: Chain Breaker
1 Replies
5. IP Networking
I have a Realtek 8139 interface in one of my machines and it will not connect to the network. /etc/rc.conf contains ifconfig_rl0="DHCP" and "rl0" was obtained from a dmesg. A network interface restart yields the following:
# /etc/rc.d/netif restart
Stopping network: lo0 rl0 fwe0 plip0.
rl0: no... (3 Replies)
Discussion started by: figaro
3 Replies
6. IP Networking
hello i have a ubuntu ssh server that i can acess from any of my comnputers but only if they are on the same wireless network as the server. i tested trhis my tehtehring my samsung blackjack to my windows partition and installing openssh to windows it works when windows is on the wireless but no... (1 Reply)
Discussion started by: old noob
1 Replies
7. IP Networking
Hi
I have an Apache Web server running on a Solaris 8 box that sits on a SSN.
I have one desktop that connects to the SSN from the internal network and is recognised directly without using the gateway, all other desktops, laptops from inside the internal network connect to the SSN using the... (0 Replies)
Discussion started by: Bobby76
0 Replies
8. HP-UX
Hie everyone,
I am currently facing a problem whereby I can not connect to an external network from a package ip address on a HP-UX cluster. Below is the illustration:
Primary Server IP Address : n.n.n.202
Secondary Server IP Address : n.n.n.212
Package IP Address : n.n.n.211
... (1 Reply)
Discussion started by: cchilenga
1 Replies
9. Solaris
Hi,
I've been trying to find out for the past two days how to set my Solaris 10 to join wireless network (Airport base station with ACL and wep or wpa on).
Using ethernet is a bit out of question as I don't have an ethernet cable that would reach the other side of the house.
Solaris 10... (1 Reply)
Discussion started by: giax
1 Replies
10. Solaris
I have just installed Solaris 10 (x86) on my PC, which is connected to an ISP via a Netgear DG834G firewall/modem router. I can't find the network. My router has the IP address 192.168.0.1 and my ISP assigned IP address is 214.159.X.Y
I have edited various files based upon information I have... (7 Replies)
Discussion started by: christian_hicks
7 Replies
bssh/bvnc/bshell(1) General Commands Manual bssh/bvnc/bshell(1)
NAME
bssh/bvnc/bshell - Browse for SSH/VNC servers on the local network
SYNOPSIS
bssh
bvnc
bshell
DESCRIPTION
bssh/bvnc/bshell browses for SSH/VNC servers on the local network, shows them in a GUI for the user to select one and finally calls
ssh/vncviewer after a selection was made.
If the binary is called as bssh only ssh servers will be shown. If the binary is called as bvnc only VNC servers will be shown. If the
binary is called as bshell both VNC and SSH servers are shown.
OPTIONS
-s | --ssh
Browse for SSH servers (and only SSH servers) regardless under which name the binary is called.
-v | --vnc
Browse for VNC servers (and only VNC servers) regardless under which name the binary is called.
-S | --shell
Browse for both VNC and SSH servers regardless under which name the binary is called.
-d | --domain= DOMAIN
Browse in the specified domain. If omitted bssh/bvnc/bshell will browse in the default browsing domain (usually .local)
-h | --help
Show help.
AUTHORS
The Avahi Developers <avahi (at) lists (dot) freedesktop (dot) org>; Avahi is available from http://avahi.org/
SEE ALSO
avahi-browse(1), ssh(1), vncviewer(1)
COMMENTS
This man page was written using xml2man(1) by Oliver Kurth.
Manuals User bssh/bvnc/bshell(1)
Connecting using SSH in WAN network