8 More Discussions You Might Find Interesting
1. Red Hat
HI,
Can you guys help me to install redhat cluster on VMware Workstation.
How to download cluster suite and how to configure on Workstation. (1 Reply)
Discussion started by: karthik9358
1 Replies
2. Red Hat
Hello Experts,
Please help me with the exact steps on configuring two node cluster on RHEL 6.2,
I failed to configure the simplest cluster by below steps,
1- install RHEL 6.2 64-bit on both nodes
2- add to hosts file of each server ( 1 IP in local NW and another in IP private NW).
x.x.x.x ... (1 Reply)
Discussion started by: karmellove
1 Replies
3. Red Hat
Hi,
is it normal, that the IP alias (service IP) can't be seen with ifconfig -a , as eth0:1 for example
the IP is on the node, you can ping it, and open ports for that IP
look at this:
# ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue
link/loopback... (4 Replies)
Discussion started by: funksen
4 Replies
4. Red Hat
Hi Friends,
I am trying to configure redhat high availability cluster on rhel5 32bit.
As i am not having the RHN subscription, I have to intsall all the cluster suite manually. I am not aware what all are the rpms needs to be installed. Please let me know about the rpms needs to be installed.... (3 Replies)
Discussion started by: arumon
3 Replies
5. Solaris
Hi,
I am configuring the sun cluster between two nodes. It is asking me to create a filesystem called globaldevices in root and mount it permanently. I created a new slice c0t0d0s3 and created a filesytem /globaldevices. How can I mount it permanently. I know we have to do it /etc/vfstab, but... (3 Replies)
Discussion started by: gunnervarma
3 Replies
6. Solaris
Hi Gurus,
For learning purpose, I have installed a single node cluster 3.2 on Solaris 10 for practice. Now I am welling to create two non-global zone and create them as a fail over. Will appreciate your help and assistance.
Thanks (3 Replies)
Discussion started by: newadmin
3 Replies
7. High Performance Computing
Hi,
I am relatively new to Sun Solaris. I am installing 2 node cluster and when I was installing cluster suite 3.2 2/08, it is giving me this error as "Conflict - Incomplete version detected".
Please help me in this regard and also suggest me any valuable point to consider before going ahead... (3 Replies)
Discussion started by: hi2joshi
3 Replies
8. Linux
Hi,
I have a Redhat Cluster Suite with 2 nodes, using option "Multicast HeartBeating" on clumembd, whith default IP: 225.0.0.11
The cluster member names are:
# grep node /etc/hosts
192.168.100.1 node1
192.168.100.2 node2
My problem is that the Multicast IP is relating to other network... (1 Reply)
Discussion started by: Livio
1 Replies
cmruncl(1m) cmruncl(1m)
NAME
cmruncl - run a high availability cluster
SYNOPSIS
cmruncl [-f] [-v] [-n node_name...] [-t | -w none]
DESCRIPTION
cmruncl causes all nodes in a configured cluster or all nodes specified to start their cluster daemons and form a new cluster.
To start a cluster, a user must either be superuser(UID=0), or have an access policy of FULL_ADMIN allowed in the cluster configuration
file. See access policy in cmquerycl(1m).
This command should only be run when the cluster is not active on any of the configured nodes. This command verifies the network configu-
ration before causing the nodes to start their cluster daemons. If a cluster is already running on a subset of the nodes, the cmrunnode
command should be used to start the remaining nodes and force them to join the existing cluster.
If node_name is not specified, the cluster daemons will be started on all the nodes in the cluster. All nodes in the cluster must be
available for the cluster to start unless a subset of nodes is specified.
Options
cmruncl supports the following options:
-f Force cluster startup without warning message and continuation prompt that are printed with the -n option.
-v Verbose output will be displayed.
-t Test only. Provide an assessment of the package placement without affecting the current state of the nodes or packages.
The -w option is not required with the -t option as -t does not validate network connectivity, but assumes that all the
nodes can meet any external dependencies such as EMS resources, package subnets, and storage.
-n node_name...
Start the cluster daemon on the specified subset of node(s).
-w none By default network probing is performed to check that the network connectivity is the same as when the cluster was config-
ured. Any anomalies are reported before the cluster daemons are started. The -w none option disables this probing. The
option should only be used if this network configuration is known to be correct from a recent check.
RETURN VALUE
cmruncl returns the following value:
0 Successful completion.
1 Command failed.
EXAMPLES
Run the cluster daemon:
cmruncl
Run the cluster daemons on node1 and node2:
cmruncl -n node1 -n node2
AUTHOR
cmruncl was developed by HP.
SEE ALSO
cmquerycl(1m), cmhaltcl(1m), cmhaltnode(1m), cmrunnode(1m), cmviewcl(1m), cmeval(1m).
Requires Optional Serviceguard Software cmruncl(1m)
