9 More Discussions You Might Find Interesting
1. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
2. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
3. Red Hat
Hello friends
Today i have changed my passwd policy for strong password
Everything is working correctly but when i changed my password , it did not ask me my old password
my /etc/pam.d/system-auth file is (only passwdqc.so module line)
password required pam_passwdqc.so retry=3... (0 Replies)
Discussion started by: rink
0 Replies
4. Linux
Hi gud day,
I would like to ask if possible to load the driver i compiled module without installing it in the ubuntu-kernel-distro/updates* or simple not executing "make install". what i mean is i compile the compat wireless driver using make and i want to try to load
on the system without... (1 Reply)
Discussion started by: jao_madn
1 Replies
5. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
6. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
7. Programming
cannot generate .ko file on my linux, although it can generate module.symvers.
But when I copy .c file and Makefile to another linux computer, there's no problem.
The strange thing is: make is successfuly executed, and returned 0;
make output:
make -C /lib/modules/2.6.18-92.el5xen/build ... (4 Replies)
Discussion started by: vistastar
4 Replies
8. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
9. Linux
Hi all,
I am working on USB data monitoring on Fedora Core 9. Kernel 2.6.25 has a built-in module (the one that isn't loadable, but compiles and links statically with the kernel during compilation) to snoop USB data. It is in <kernel_source_code>/drivers/usb/mon/.
I need to know if I can... (0 Replies)
Discussion started by: anitemp
0 Replies
UCHCOM(4) BSD Kernel Interfaces Manual UCHCOM(4)
NAME
uchcom -- WinChipHead CH341/CH340 serial adapter driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device uchcom
device ucom
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
uchcom_load="YES"
DESCRIPTION
The uchcom driver provides support for the WinChipHead CH341/CH340 USB-to-RS-232 Bridge chip.
The device is accessed through the ucom(4) driver which makes it behave like a tty(4).
HARDWARE
The uchcom driver supports the following adapters:
o HL USB-RS232
SEE ALSO
tty(4), ucom(4), usb(4)
HISTORY
The uchcom driver first appeared in NetBSD. The first FreeBSD release to include it was FreeBSD 8.0.
BUGS
Actually, this chip seems unable to drive other than 8 data bits and 1 stop bit line.
BSD
May 18, 2009 BSD