mbadblocks(1) [suse man page]

mbadblocks(1) General Commands Manual mbadblocks(1)

Name
mbadblocks - tests a floppy disk, and marks the bad blocks in the FAT

Note of warning
This manpage has been automatically generated from mtools's texinfo documentation, and may not be entirely accurate or complete. See the
end of this man page for details.

Description
The mbadblocks command is used to scan an MS-DOS floppy and mark its unused bad blocks as bad. It uses the following syntax:

mbadblocks drive:

Mbadblocks scans an MS-DOS floppy for bad blocks. All unused bad blocks are marked as such in the FAT. This is intended to be used right
after mformat. It is not intended to salvage bad disks.

Bugs
Mbadblocks should (but doesn't yet :-( ) also try to salvage bad blocks which are in use by reading them repeatedly, and then mark them
bad.

See Also
Mtools' texinfo doc

Viewing the texi doc
This manpage has been automatically generated from mtools's texinfo documentation. However, this process is only approximative, and some
items, such as crossreferences, footnotes and indices are lost in this translation process. Indeed, these items have no appropriate repre-
sentation in the manpage format. Moreover, not all information has been translated into the manpage version. Thus I strongly advise you
to use the original texinfo doc. See the end of this manpage for instructions how to view the texinfo doc.

* To generate a printable copy from the texinfo doc, run the following commands:

./configure; make dvi; dvips mtools.dvi

* To generate a html copy, run:

./configure; make html

A premade html can be found at `http://www.gnu.org/software/mtools/manual/mtools.html'

* To generate an info copy (browsable using emacs' info mode), run:

./configure; make info

The texinfo doc looks most pretty when printed or as html. Indeed, in the info version certain examples are difficult to read due to the
quoting conventions used in info.

mtools-4.0.13 28Feb10 mbadblocks(1)

Check Out this Related Man Page

mmd(1)							      General Commands Manual							    mmd(1)

Name
       mmd - make an MSDOS subdirectory

Note of warning
       This  manpage  has been automatically generated from mtools's texinfo documentation, and may not be entirely accurate or complete.  See the
       end of this man page for details.

Description
       The mmd command is used to make an MS-DOS subdirectory. Its syntax is:

       mmd [-D clash_option] msdosdirectory [ msdosdirectories... ]

       Mmd makes a new directory on an MS-DOS file system. An error occurs if the directory already exists.

See Also
       Mtools' texinfo doc

Viewing the texi doc
       This manpage has been automatically generated from mtools's texinfo documentation. However, this process is only  approximative,  and  some
       items, such as crossreferences, footnotes and indices are lost in this translation process.  Indeed, these items have no appropriate repre-
       sentation in the manpage format.  Moreover, not all information has been translated into the manpage version.  Thus I strongly  advise  you
       to use the original texinfo doc.  See the end of this manpage for instructions how to view the texinfo doc.

       *      To generate a printable copy from the texinfo doc, run the following commands:

		     ./configure; make dvi; dvips mtools.dvi

       *      To generate a html copy,	run:

		     ./configure; make html

       A premade html can be found at `http://www.gnu.org/software/mtools/manual/mtools.html'

       *      To generate an info copy (browsable using emacs' info mode), run:

		     ./configure; make info

       The  texinfo  doc looks most pretty when printed or as html.  Indeed, in the info version certain examples are difficult to read due to the
       quoting conventions used in info.

mtools-4.0.13							      28Feb10								    mmd(1)

Linux and UNIX Man Pages

mbadblocks(1) [suse man page]

Check Out this Related Man Page