fs_wrapper(5) [hpux man page]

fs_wrapper(5)							File Formats Manual						     fs_wrapper(5)

NAME

       fs_wrapper - configuration and binary files used by file system administration commands

SYNOPSIS

       FStype] ...

       FStype] ...

       FStype] ...

       FStype] ...

       FStype] ...

       FStype] ...

       FStype] ...

       FStype] ...

       FStype] ...

       FStype] ...

       FStype] ...

DESCRIPTION

       The  commands  listed  in the SYNOPSIS can operate on different types of file systems.  Each command (except for reads file system specific
       configuration files that control the command's behavior, and invokes a file system specific binary file to do the actual work.	FStype	is
       the  file system type as optionally specified on the command line.  If FStype is not given, then the file system type is determined from by
       matching an entry in this file with a device provided with the command (see individual commands for details of usage).

       Administrators may also define a default file system type for the above commands via the file If this file exists, and contains the line:

       (e.g., then the above commands will assume the FStype given in unless an FStype is provided on the command line or is in The  default  file
       system specification is provided to maintain compatibility with pre-10.0 invocations of the commands.

       See the FILES section for a list of the files used.

WARNINGS

       The  configuration  files  are  supplied  by HP or by other file system vendors.  They are not meant to be edited by System Administrators.
       Corruption or removal of these files may lead to strange behavior, including the inability to boot.

       The format of the configuration file is subject to change.

       The file system specific binary files are not normally executed directly.  However, if the configuration files become unusable, direct exe-
       cution of these binary files may be a useful step in repairing and running the system again.  The binary files accept the same arguments as
       the commands by which they are executed.

       The command is a special case.  This command currently does not read a configuration file, and does not	execute  a  file  system  specific
       binary  file  if FStype is or The binary that handles these FStypes also processes other FStypes and calls the file system specific command
       if appropriate.

       For historical reasons, the binary files also handle and so there are no separate binary files for the latter two file systems.

       The commands (except will not work if they are renamed, because they are symbolically linked to a single executable

FILES

       FStype is the file system type as optionally specified on the command line.  command is the name of the command.

       File system specific binary files for the
					       and commands.  There may be additional file system specific binary files in this directory that are
					       not associated with

       File system specific binary files for the remaining commands.
					       There may also be other file system specific binary files in this directory that are not associated
					       with

       Configuration files for each file system type.

       File in which the default file system type can be defined.
					       If this file does not exist, there is no default file system type.

       Static information about the file systems

SEE ALSO

       ff(1M), fsck(1M), fsdb(1M), mkfs(1M), mount(1M), ncheck(1M), newfs(1M), quot(1M), quotacheck(1M), volcopy(1M), fstab(4).

																     fs_wrapper(5)

Check Out this Related Man Page

mountall(1M)															      mountall(1M)

NAME

       mountall, umountall - mount and unmount multiple file systems

SYNOPSIS

       FStype] [file_system_table |
       FStype]

DESCRIPTION

       is  used  to  mount  file  systems  according  to  file_system_table.  By default, is the file_system_table.  If a dash is specified, reads
       file_system_table from the standard input; the standard input must be in the same format as the

       Before each file system is mounted, a check is done using (see fsck(1M)) to ensure that the file system is mountable.  If the  file  system
       is not mountable, it is repaired by before the mount is attempted.

       causes all mounted file systems except the non-removable file systems such as to be unmounted.

   Options
       and recognize the following options:

	      Specify the file system type
			     (FStype) to be mounted or unmounted.

	      Specify action on local file systems only.

	      Specify action on remote file systems only.

	      Send a	     signal to processes that have files opened.

	      Attempt to mount all the unmounted file systems. This option will not perform the file system consistency check and repair.

	      Perform the file system consistency check and repair on all unmounted file system. This option will not mount the file systems.

DIAGNOSTICS

       Error and warning messages may originate from or See fsck(1M), mount(1M), or fuser(1M) to interpret the error and warning messages.

EXAMPLES

       Mount all unmounted file systems listed in

       Mount all local file systems listed in

       Mount all remote file systems listed in

       Mount all local hfs file systems:

       Unmount all NFS file systems and kill any processes that have files opened in the file system:

WARNINGS

       especially with the option, should be used with extreme caution, because it can cause severe damage.

       The option may not be available in future releases.

       may not be effective with some cases of LOFS file systems.

FILES

       Static information about the file systems
       Mounted file system table

SEE ALSO

       fsck(1M), mount(1M), fuser(1M), mnttab(4), fstab(4), signal(2)

																      mountall(1M)

Linux and UNIX Man Pages

fs_wrapper(5) [hpux man page]

Check Out this Related Man Page