_STARTNETKEY(8) [FIXME: manual] _STARTNETKEY(8)NAME
ipsec__startnetkey - internal script to bring up kernel components for netkey (xfrm)
DESCRIPTION
_startnetkey brings up the Openswan kernel component. This involves loading any required modules.
SEE ALSO ip(8), ipsec_tncfg(8).
BUGS
The ip xfrm commands are not documented in the man page. Ask linux-net people, but do not hold your breath. See ip xfrm state help and ip
xfrm policy help for the magic words.
HISTORY
Man page written for the Linux Openswan project <http://www.openswan.org/> by Michael Richardson.
[FIXME: source] 10/06/2010 _STARTNETKEY(8)
Check Out this Related Man Page
IPSEC_ADDCONN(8) [FIXME: manual] IPSEC_ADDCONN(8)NAME
ipsec_addconn - load a given policy into the pluto IKE daemon
SYNOPSIS
ipsec addconn --configsetup [--rootdir dir] [--config filename] [--ctlbase socketfile]
ipsec addconn --addall [--rootdir dir] [--config filename] [--ctlbase socketfile] [--defaultroute addr] [--defaultroutenexthop addr]
ipsec addconn [--rootdir dir] [--config filename] [--ctlbase socketfile] [--defaultroute addr] [--defaultroutenexthop addr] name1
[name2 ..]
ipsec addconn [--listroute] [--liststart] [--rootdir dir] [--config filename] [--ctlbase socketfile]
ipsec addconn --help
DESCRIPTION
ipsec addconn takes a config file (or stdin) containing the format of ipsec.conf, or the format of individual "conn" sections, and uses
that information to load named or all connections defined in that configuration file into the running openswan pluto IKE daemon. If no
configuration file is specified, the default configuration file is used. If no pluto socket is specified, the default socket location will
be used.
When --addall is used, all connections defined in the config file will be operated on. Otherwise, only the specified connection names will
be affected.
When addcon is run, connections that have the auto= option set to add, start or route will be loaded, routed or initiated. If a connection
was loaded or initiated already, it will be replaced.
When --configsetup is specified, the configuration file is parsed for the config setup section and printed to the terminal usable as a
shell script.
When --listroute or --liststart is specified, no connections are added or replaced, only shown. This command can be used to verify which
connections the addcon command would act upon, without actually performing any action.
HISTORY
Man page written for the Xelerance Openswan project <http://www.openswan.org/> by Paul Wouters
[FIXME: source] 10/06/2010 IPSEC_ADDCONN(8)
I have a huge matrix file containing some 1.5 million rows and 6000 columns. The matrix looks something like this:
1 2 3
4 5 6
7 8 9
3 4 5
I want to add all the numbers in the columns of this matrix and display the result to my stdout. This means that the numbers in the first column are:
... (2 Replies)
Hi,
Just trying to get to grips with sed and awk for some reporting for work and I need some assistance:
I have a file that lists policy names on the first line and then on the second line whether the policy is active or not.
Policy Name: Policy1
Active: yes
Policy... (8 Replies)
version info :
vi availabe with RHEL 5.4
I have a text file with 10,000 lines. I want to copy lines from 5000th line to 7000th and redirect to a file. Any idea how I can do this?
Note:
The above scenario is just an example. In my actual requirement, the file has 14 million lines and I want... (9 Replies)
Hi everyone,
I know the following questions are noobish questions but I am asking them because I am confused about the basics of history behind UNIX and LINUX.
Ok onto business, my questions are-:
Was/Is UNIX ever an open source operating system ?
If UNIX was... (21 Replies)
Hello,
I couldn't find an actual introduction thread, so I decided to just put this here.
I go by d0wngrade online. I have been programming in multiple languages for about 15+ years. I started with standard web design languages like HTML and CSS, but I then advanced from design to development... (2 Replies)
Hi guys...
The first active code line in AudioScope.sh is set -u .
This causes a complete exit if a variable is used/found but has not been allocated at the start of the program.
However, apart from writing code to do the task, is there a switch to to check which variables have been... (17 Replies)
Hi.
In thread https://www.unix.com/shell-programming-and-scripting/267833-grouping-counting.html rovf and I had a mini-discussion on grep and awk.
Here is a demo script that compares the awk and grep approaches for this single problem:
#!/usr/bin/env bash
# @(#) s2 Demonstrate group... (1 Reply)
Hello,
I have to fish out some specific columns from a file based on the header value. I have the list of columns I need in a different file. I thought I could read in the list of headers I need,
# file with header names of required columns in required order
headers_file=$2
# read contents... (11 Replies)
For those interested in installing dash shell on OSX Lion to help test POSIX compliancy of shell scripts, it is quite easy. I did it like this:
If you don't have gcc on your system:
0. Download and install the Command Line Tools for Xcode package from Sign In - Apple *
1. Download the dash... (2 Replies)
Hello and thanks in advance for any help anyone can offer me
I'm trying to learn the find command and thought I was understanding it... Apparently I was wrong. I was doing compound searches and I started getting weird results with the -size test. I was trying to do a search on a 1G file owned by... (14 Replies)
I have data of an excel files as given below,
file1
org1_1 1 1 2.5 100
org1_2 1 2 5.5 98
org1_3 1 3 7.2 88
file2
org2_1 1 1 2.5 100
org2_2 1 2 5.5 56
org2_3 1 3 7.2 70
I have multiple excel files as above shown.
I have to copy column 1, column 4 and paste into a new excel file as... (26 Replies)
Dear All,
Taking a break from Vue.js coding for the site, SEO and YT videos; and hopefully addressing some well deserved criticism from some here that I have been too focused on the visual aspects of the forums versus the substance and the community....
While the "current generation... (9 Replies)
Hi all...
Well guys and gals, I jumped in at the deep end and found things that PERL cannot do by default.
Many tricky terminal escape codes are not catered for so I had to create workarounds.
One thing I searched for was this:
Passing perl variable to shell command
AND, @Neo this was... (15 Replies)