XMINICOM(1) Linux Users Manual XMINICOM(1)NAME
xminicom - friendly serial communication program
SYNOPSIS
xminicom minicom-options
DESCRIPTION
Xminicom is a script wrapper around minicom. It tries to find a color capable xterm or rxvt on your system, and then runs minicom with the
-c (color) flag in a terminal session.
OPTIONS
See minicom (1).
AUTHOR
Miquel van Smoorenburg, miquels@cistron.nl
SEE ALSO minicom(1)
September 14, 1998 XMINICOM(1)
Check Out this Related Man Page
ASCII-XFR(1) Linux Users Manual ASCII-XFR(1)NAME
ascii-xfr - upload/download files using the ASCII protocol
SYNOPSIS
ascii-xfr -s|-r [-ednv] [-l linedelay] [-c characterdelay] filename
DESCRIPTION
Ascii-xfr Transfers files in ASCII mode. This means no flow control, no checksumming and no file-name negotiation. It should only be used
if the remote system doesn't understand anything else.
The ASCII protocol transfers files line-by-line. The EOL (End-Of-Line) character is transmitted as CRLF. When receiving, the CR character
is stripped from the incoming file. The Control-Z (ASCII 26) character signals End-Of-File, if option -e is specified (unless you change
it to Cotrol-D (ASCII 4) with -d).
Ascii-xfr reads from stdin when receiving, and sends data on stdout when sending. Some form of input or output redirection to the modem
device is thus needed when downloading or uploading, respectively.
OPTIONS -s Send a file.
-r Receive a file. One of -s or -r must be present.
-e Send the End-Of-File character (Control-Z, ASCII 26 by default) when uploading has finished.
-d Use the Control-D (ASCII 4) as End-Of-File character.
-n Do not translate CR to CRLF and vice versa.
-v Verbose: show tranfer statistics on the stderr output.
-l milliseconds
When transmitting, pause for this delay after each line.
-c milliseconds
When transmitting, pause for this delay after each character.
file Name of the file to send or receive. When receiving, any existing file by this name will be truncated.
USAGE WITH MINICOM
If you want to call this program from minicom(1), start minicom and go to the Options menu. Select File transfer protocols. Add the fol-
lowing lines, for example as protocols I and J.
I Ascii /usr/bin/ascii-xfr -sv Y U N Y
J Ascii /usr/bin/ascii-xfr -rv Y D N Y
AUTHOR
Miquel van Smoorenburg, miquels@cistron.nl
Jukka Lahtinen, walker@netsonic.fi
SEE ALSO minicom(1)
$Date: 2006/10/28 14:35:59 $ ASCII-XFR(1)
I have a huge matrix file containing some 1.5 million rows and 6000 columns. The matrix looks something like this:
1 2 3
4 5 6
7 8 9
3 4 5
I want to add all the numbers in the columns of this matrix and display the result to my stdout. This means that the numbers in the first column are:
... (2 Replies)
Hi,
Just trying to get to grips with sed and awk for some reporting for work and I need some assistance:
I have a file that lists policy names on the first line and then on the second line whether the policy is active or not.
Policy Name: Policy1
Active: yes
Policy... (8 Replies)
version info :
vi availabe with RHEL 5.4
I have a text file with 10,000 lines. I want to copy lines from 5000th line to 7000th and redirect to a file. Any idea how I can do this?
Note:
The above scenario is just an example. In my actual requirement, the file has 14 million lines and I want... (9 Replies)
Hi everyone,
I know the following questions are noobish questions but I am asking them because I am confused about the basics of history behind UNIX and LINUX.
Ok onto business, my questions are-:
Was/Is UNIX ever an open source operating system ?
If UNIX was... (21 Replies)
Hello,
I couldn't find an actual introduction thread, so I decided to just put this here.
I go by d0wngrade online. I have been programming in multiple languages for about 15+ years. I started with standard web design languages like HTML and CSS, but I then advanced from design to development... (2 Replies)
Hi guys...
The first active code line in AudioScope.sh is set -u .
This causes a complete exit if a variable is used/found but has not been allocated at the start of the program.
However, apart from writing code to do the task, is there a switch to to check which variables have been... (17 Replies)
Hi.
In thread https://www.unix.com/shell-programming-and-scripting/267833-grouping-counting.html rovf and I had a mini-discussion on grep and awk.
Here is a demo script that compares the awk and grep approaches for this single problem:
#!/usr/bin/env bash
# @(#) s2 Demonstrate group... (1 Reply)
Hello,
I have to fish out some specific columns from a file based on the header value. I have the list of columns I need in a different file. I thought I could read in the list of headers I need,
# file with header names of required columns in required order
headers_file=$2
# read contents... (11 Replies)
For those interested in installing dash shell on OSX Lion to help test POSIX compliancy of shell scripts, it is quite easy. I did it like this:
If you don't have gcc on your system:
0. Download and install the Command Line Tools for Xcode package from Sign In - Apple *
1. Download the dash... (2 Replies)
Hello and thanks in advance for any help anyone can offer me
I'm trying to learn the find command and thought I was understanding it... Apparently I was wrong. I was doing compound searches and I started getting weird results with the -size test. I was trying to do a search on a 1G file owned by... (14 Replies)
I have data of an excel files as given below,
file1
org1_1 1 1 2.5 100
org1_2 1 2 5.5 98
org1_3 1 3 7.2 88
file2
org2_1 1 1 2.5 100
org2_2 1 2 5.5 56
org2_3 1 3 7.2 70
I have multiple excel files as above shown.
I have to copy column 1, column 4 and paste into a new excel file as... (26 Replies)
Dear All,
Taking a break from Vue.js coding for the site, SEO and YT videos; and hopefully addressing some well deserved criticism from some here that I have been too focused on the visual aspects of the forums versus the substance and the community....
While the "current generation... (9 Replies)
Hi all...
Well guys and gals, I jumped in at the deep end and found things that PERL cannot do by default.
Many tricky terminal escape codes are not catered for so I had to create workarounds.
One thing I searched for was this:
Passing perl variable to shell command
AND, @Neo this was... (15 Replies)