MYTHTV-RECORDING-SOON(1) General Commands Manual MYTHTV-RECORDING-SOON(1)NAME
mythtv_recording_soon - test whether a MythTV backend will be recording soon
SYNOPSIS
mythtv_recording_soon [ time in seconds ]
DESCRIPTION
mythtv_recording_soon checks to see if a MythTV backend is currently recording, or will be recording soon. It checks the host which is
configured in /etc/default/mythtv-status with the HOST setting.
time in seconds is how long "soon" is considered to be. It defaults to 600 (10 minutes).
OPTIONS
None
EXIT STATUS
0 MythTV backend is recording now, or will be recording soon
1 MythTV backend is not recording now and won't be recording soon
FILES
/etc/default/mythtv-status Config file
SEE ALSO mythtv-status(1), mythtv_recording_now(1).
AUTHOR
mythtv_recording_soon and this manpage were written by Andrew Ruthven <andrew@etc.gen.nz>.
2008-04-19 MYTHTV-RECORDING-SOON(1)
Check Out this Related Man Page
record(1) General Commands Manual record(1)NAME
record - records *.wav files
SYNOPSIS
record [ options ]
DESCRIPTION
record records *.wav files in CD quality (i.e. 44100 Hz, 16bit, stereo). It has a input level meter, which might be useful for sound trou-
ble shooting (check if the mixer settings ok for recording from the TV card etc.)
OPTIONS -h display help text
-o file
basename for the output file(s), a number and the .wav extension are added by record. Default is "record".
-i dev mixer control. This should be the one where you can adjust the record level for your audio source. Default is "line". "mic" and
"igain" are good candidates too. Best way to figure is to start your favorite mixer tool and check out which one works ...
-m dev set mixer device. Default is "/dev/mixer".
-d dev set audio device. Default is "/dev/dsp".
-r rate
set sample rate. Default is 44100.
-p sec peak seconds (number of seconds which should be scanned for the volume maximum). This affects both peak level display and level
triggered recording (see below). Default is 1.5 seconds.
record can also be used non-interactive:
-c enable console (non-interactive) mode.
-v be verbose (console mode only).
-t mm:ss
Limit the record time (console mode only). By default record records until stopped by a signal (by typing ^C for example).
-s size
Limit the file size (console mode only). record will continue with a new file once the limit is reached.
-n num Limit the file count (console mode only). record will stop recording after num files.
-l Enable level triggered recording (console mode only) with the default trigger level (1000).
-L level
Enable level triggered recording with the specified trigger level.
If level triggered recording is active, record will start and stop recording depending on the signal strength. Recording will be started
if the signal strength is above the trigger level (1000/32768 => around 3%). Recording will be stopped if the signal is below the trigger
level for some time (1.5 seconds by default, the -p switch changes this).
AUTHOR
Gerd Knorr <kraxel@bytesex.org>
(c) Gerd Knorr record(1)
I have a huge matrix file containing some 1.5 million rows and 6000 columns. The matrix looks something like this:
1 2 3
4 5 6
7 8 9
3 4 5
I want to add all the numbers in the columns of this matrix and display the result to my stdout. This means that the numbers in the first column are:
... (2 Replies)
Hi,
Just trying to get to grips with sed and awk for some reporting for work and I need some assistance:
I have a file that lists policy names on the first line and then on the second line whether the policy is active or not.
Policy Name: Policy1
Active: yes
Policy... (8 Replies)
version info :
vi availabe with RHEL 5.4
I have a text file with 10,000 lines. I want to copy lines from 5000th line to 7000th and redirect to a file. Any idea how I can do this?
Note:
The above scenario is just an example. In my actual requirement, the file has 14 million lines and I want... (9 Replies)
Hi everyone,
I know the following questions are noobish questions but I am asking them because I am confused about the basics of history behind UNIX and LINUX.
Ok onto business, my questions are-:
Was/Is UNIX ever an open source operating system ?
If UNIX was... (21 Replies)
Hello,
I couldn't find an actual introduction thread, so I decided to just put this here.
I go by d0wngrade online. I have been programming in multiple languages for about 15+ years. I started with standard web design languages like HTML and CSS, but I then advanced from design to development... (2 Replies)
Hi guys...
The first active code line in AudioScope.sh is set -u .
This causes a complete exit if a variable is used/found but has not been allocated at the start of the program.
However, apart from writing code to do the task, is there a switch to to check which variables have been... (17 Replies)
Hi.
In thread https://www.unix.com/shell-programming-and-scripting/267833-grouping-counting.html rovf and I had a mini-discussion on grep and awk.
Here is a demo script that compares the awk and grep approaches for this single problem:
#!/usr/bin/env bash
# @(#) s2 Demonstrate group... (1 Reply)
Hello,
I have to fish out some specific columns from a file based on the header value. I have the list of columns I need in a different file. I thought I could read in the list of headers I need,
# file with header names of required columns in required order
headers_file=$2
# read contents... (11 Replies)
For those interested in installing dash shell on OSX Lion to help test POSIX compliancy of shell scripts, it is quite easy. I did it like this:
If you don't have gcc on your system:
0. Download and install the Command Line Tools for Xcode package from Sign In - Apple *
1. Download the dash... (2 Replies)
Hello and thanks in advance for any help anyone can offer me
I'm trying to learn the find command and thought I was understanding it... Apparently I was wrong. I was doing compound searches and I started getting weird results with the -size test. I was trying to do a search on a 1G file owned by... (14 Replies)
I have data of an excel files as given below,
file1
org1_1 1 1 2.5 100
org1_2 1 2 5.5 98
org1_3 1 3 7.2 88
file2
org2_1 1 1 2.5 100
org2_2 1 2 5.5 56
org2_3 1 3 7.2 70
I have multiple excel files as above shown.
I have to copy column 1, column 4 and paste into a new excel file as... (26 Replies)
Dear All,
Taking a break from Vue.js coding for the site, SEO and YT videos; and hopefully addressing some well deserved criticism from some here that I have been too focused on the visual aspects of the forums versus the substance and the community....
While the "current generation... (9 Replies)
Hi all...
Well guys and gals, I jumped in at the deep end and found things that PERL cannot do by default.
Many tricky terminal escape codes are not catered for so I had to create workarounds.
One thing I searched for was this:
Passing perl variable to shell command
AND, @Neo this was... (15 Replies)