ELVFMT(1) User commands ELVFMT(1)NAME
elvfmt - adjust line-length for paragraphs of text
SYNOPSIS
elvfmt [-w width | -width] [-s] [-c] [-i chars] [-C] [-M] [file]...
VERSION
This page describes the Elvis 2.2_0 version of elvfmt. See elvis(1).
DESCRIPTION
elvfmt is a simple text formatter. It inserts or deletes newlines, as necessary, to make all lines in a paragraph be approximately the
same width. It preserves indentation and word spacing.
If you don't name any files on the command line, then elvfmt will read from stdin.
It is typically used from within vi(1) or elvis(1) to adjust the line breaks in a single paragraph. To do this, move the cursor to the top
of the paragraph, type "!}elvfmt", and hit <Return>.
OPTIONS -w width or -width
Use a line width of width characters instead of the default of 72 characters.
-s Don't join lines shorter than the line width to fill paragraphs.
-c Try to be smarter about crown margins. Specifically, this tells elvfmt to expect the first line of each paragraph to have a differ-
ent indentation than subsequent lines. If text from the first input line is wrapped onto the second output line, then elvfmt will
scan ahead to figure out what indentation it should use for the second output line, instead of reusing the first line's indentation.
-i chars
Allow the indentation text to include any character from chars, in addition to spaces and tabs. You should quote the chars list to
protect it from the shell.
-C and -M
These are shortcuts for combinations of other flags. is short for and is useful for reformatting C/C++ comments. is short for
and is useful for reformatting email messages.
SEE ALSO vi(1), elvis(1)AUTHOR
Steve Kirkendall
kirkenda@cs.pdx.edu
ELVFMT(1)
Check Out this Related Man Page
FMT(1) BSD General Commands Manual FMT(1)NAME
fmt -- simple text formatter
SYNOPSIS
fmt [-cmnps] [-d chars] [-l num] [-t num] [goal [maximum] | -width | -w width] [file ...]
DESCRIPTION
The fmt utility is a simple text formatter which reads the concatenation of input files (or standard input if none are given) and produces on
standard output a version of its input with lines as close to the goal length as possible without exceeding the maximum. The goal length
defaults to 65 and the maximum to 10 more than the goal length. Alternatively, a single width parameter can be specified either by prepend-
ing a hyphen to it or by using -w. For example, ``fmt -w 72'', ``fmt -72'', and ``fmt 72 72'' all produce identical output. The spacing at
the beginning of the input lines is preserved in the output, as are blank lines and interword spacing. Lines are joined or split only at
white space; that is, words are never joined or hyphenated.
The options are as follows:
-c Center the text, line by line. In this case, most of the other options are ignored; no splitting or joining of lines is done.
-m Try to format mail header lines contained in the input sensibly.
-n Format lines beginning with a '.' (dot) character. Normally, fmt does not fill these lines, for compatibility with nroff(1).
-p Allow indented paragraphs. Without the -p flag, any change in the amount of whitespace at the start of a line results in a new para-
graph being begun.
-s Collapse whitespace inside lines, so that multiple whitespace characters are turned into a single space. (Or, at the end of a sen-
tence, a double space.)
-d chars
Treat the chars (and no others) as sentence-ending characters. By default the sentence-ending characters are full stop ('.'), ques-
tion mark ('?') and exclamation mark ('!'). Remember that some characters may need to be escaped to protect them from your shell.
-l number
Replace multiple spaces with tabs at the start of each output line, if possible. Each number spaces will be replaced with one tab.
The default is 8. If number is 0, spaces are preserved.
-t number
Assume that the input files' tabs assume number spaces per tab stop. The default is 8.
The fmt utility is meant to format mail messages prior to sending, but may also be useful for other simple tasks. For instance, within vis-
ual mode of the ex(1) editor (e.g., vi(1)) the command
!}fmt
will reformat a paragraph, evening the lines.
ENVIRONMENT
The LANG, LC_ALL and LC_CTYPE environment variables affect the execution of fmt as described in environ(7).
SEE ALSO fold(1), mail(1), nroff(1)HISTORY
The fmt command appeared in 3BSD.
The version described herein is a complete rewrite and appeared in FreeBSD 4.4.
AUTHORS
Kurt Shoens
Liz Allen (added goal length concept)
Gareth McCaughan
BUGS
The program was designed to be simple and fast - for more complex operations, the standard text processors are likely to be more appropriate.
When the first line of an indented paragraph is very long (more than about twice the goal length), the indentation in the output can be
wrong.
The fmt utility is not infallible in guessing what lines are mail headers and what lines are not.
BSD August 2, 2004 BSD