sctp_connectx(3) [centos man page]
SCTP_CONNECTX(3) Linux Programmer's Manual SCTP_CONNECTX(3) NAME
sctp_connectx - initiate a connection on an SCTP socket using multiple destination addresses. SYNOPSIS
#include <sys/types.h> #include <sys/socket.h> #include <netinet/sctp.h> int sctp_connectx(int sd, struct sockaddr * addrs, int addrcnt, sctp_assoc_t * id); DESCRIPTION
sctp_connectx initiates a connection to a set of addresses passed in the array addrs to/from the socket sd. addrcnt is the number of addresses in the array. If sd is an IPv4 socket, the addresses passed must be IPv4 addresses. If sd is an IPv6 socket, the addresses passed can be either IPv4 or IPv6 addresses. addrs is a pointer to an array of one or more socket addresses. Each address is contained in its appropriate structure(i.e. struct sock- addr_in or struct sockaddr_in6). The family of the address type must be used to distinguish the address length. The caller specifies the number of addresses in the array with addrcnt. id is a pointer to the association id and, if provided, will be set to the identifier of the newly created association. RETURN VALUE
On success, 0 is returned. On failure, -1 is returned, and errno is set appropriately. ERRORS
EBADF sd is not a valid descriptor. ENOTSOCK sd is a descriptor for a file, not a socket. EFAULT Error while copying in or out from the user address space. EINVAL Invalid port or address. EACCES The address is protected, and the user is not the super-user. EISCONN The socket is already connected. ECONNREFUSED No one listening on the remote address. ETIMEDOUT Timeout while attempting connection. The server may be too busy to accept new connections. Note that for IP sockets the timeout may be very long when syncookies are enabled on the server. ENETUNREACH Network is unreachable. EADDRINUSE Local address is already in use. EINPROGRESS The socket is non-blocking and the connection cannot be completed immediately. It is possible to select(2) or poll(2) for comple- tion by selecting the socket for writing. After select indicates writability, use getsockopt(2) to read the SO_ERROR option at level SOL_SOCKET to determine whether connect completed successfully (SO_ERROR is zero) or unsuccessfully (SO_ERROR is one of the usual error codes listed here, explaining the reason for the failure). EALREADY The socket is non-blocking and a previous connection attempt has not yet been completed. EAGAIN No more free local ports or insufficient entries in the routing cache. For PF_INET see the net.ipv4.ip_local_port_range sysctl in ip(7) on how to increase the number of local ports. EAFNOSUPPORT The passed address didn't have the correct address family in its sa_family field. EACCES, EPERM The user tried to connect to a broadcast address without having the socket broadcast flag enabled or the connection request failed because of a local firewall rule. SEE ALSO
sctp(7) sctp_bindx(3), sctp_sendmsg(3), sctp_send(3), sctp_recvmsg(3), sctp_peeloff(3), sctp_getpaddrs(3), sctp_getladdrs(3), sctp_opt_info(3), Linux 2.6 2005-10-25 SCTP_CONNECTX(3)
Check Out this Related Man Page
CONNECT(2) Linux Programmer's Manual CONNECT(2) NAME
connect - initiate a connection on a socket SYNOPSIS
#include <sys/types.h> #include <sys/socket.h> int connect(int sockfd, const struct sockaddr *serv_addr, socklen_t addrlen); DESCRIPTION
The file descriptor sockfd must refer to a socket. If the socket is of type SOCK_DGRAM then the serv_addr address is the address to which datagrams are sent by default, and the only address from which datagrams are received. If the socket is of type SOCK_STREAM or SOCK_SEQ- PACKET, this call attempts to make a connection to another socket. The other socket is specified by serv_addr, which is an address (of length addrlen) in the communications space of the socket. Each communications space interprets the serv_addr parameter in its own way. Generally, connection-based protocol sockets may successfully connect only once; connectionless protocol sockets may use connect multiple times to change their association. Connectionless sockets may dissolve the association by connecting to an address with the sa_family mem- ber of sockaddr set to AF_UNSPEC. RETURN VALUE
If the connection or binding succeeds, zero is returned. On error, -1 is returned, and errno is set appropriately. ERRORS
The following are general socket errors only. There may be other domain-specific error codes. EBADF The file descriptor is not a valid index in the descriptor table. EFAULT The socket structure address is outside the user's address space. ENOTSOCK The file descriptor is not associated with a socket. EISCONN The socket is already connected. ECONNREFUSED No one listening on the remote address. ETIMEDOUT Timeout while attempting connection. The server may be too busy to accept new connections. Note that for IP sockets the timeout may be very long when syncookies are enabled on the server. ENETUNREACH Network is unreachable. EADDRINUSE Local address is already in use. EINPROGRESS The socket is non-blocking and the connection cannot be completed immediately. It is possible to select(2) or poll(2) for comple- tion by selecting the socket for writing. After select indicates writability, use getsockopt(2) to read the SO_ERROR option at level SOL_SOCKET to determine whether connect completed successfully (SO_ERROR is zero) or unsuccessfully (SO_ERROR is one of the usual error codes listed here, explaining the reason for the failure). EALREADY The socket is non-blocking and a previous connection attempt has not yet been completed. EAGAIN No more free local ports or insufficient entries in the routing cache. For PF_INET see the net.ipv4.ip_local_port_range sysctl in ip(7) on how to increase the number of local ports. EAFNOSUPPORT The passed address didn't have the correct address family in its sa_family field. EACCES, EPERM The user tried to connect to a broadcast address without having the socket broadcast flag enabled or the connection request failed because of a local firewall rule. CONFORMING TO
SVr4, 4.4BSD (the connect function first appeared in BSD 4.2). SVr4 documents the additional general error codes EADDRNOTAVAIL, EINVAL, EAFNOSUPPORT, EALREADY, EINTR, EPROTOTYPE, and ENOSR. It also documents many additional error conditions not described here. NOTE
The third argument of connect is in reality an int (and this is what BSD 4.* and libc4 and libc5 have). Some POSIX confusion resulted in the present socklen_t. The draft standard has not been adopted yet, but glibc2 already follows it and also has socklen_t. See also accept(2). BUGS
Unconnecting a socket by calling connect with a AF_UNSPEC address is not yet implemented. SEE ALSO
accept(2), bind(2), listen(2), socket(2), getsockname(2) Linux 2.2 1998-10-03 CONNECT(2)