Login or Register to Ask a Question and Join Our Community


IP Networking

Unix Network Routes

Login to Discuss or Reply to this Discussion in Our Community

 
Thread Tools Search this Thread
Special Forums IP Networking Unix Network Routes
# 1  
Old 03-09-2010
Unix Network Routes
I would really appreciate some help with HP UX's Network Routes.

Basically, what I want to do is, I would want a system with global ip (eg: 202.144.138.122) to ping/access my HP-UX server which is with private IP address (192.168.1.23). I have all the routers/switches in between properly route traffic between global and private ips, but I can't understand what to insert into my network route table in HP-UX system via SAM.

When i ping 192.168.1.23 from 202.144.138.122, there is no response.. But when I plug in a windows system with the ip 192.168.1.23, it can be accessed via the 202.xxx.xxx.xxx ip. So, the problem is with the Unix route.

What values do I have to insert into the network route on my HP - UX machine(192.168.1.23)

The gateway for HP-UX is 192.168.1.1, and the gateway for global ip is (202.144.138.137).

Thank you.
# 2  
Old 03-26-2010
Can you post the output of netstat -nr, and netstat -in from the HPUX system?
# 3  
Old 03-27-2010
can you be more specific....about the scenario
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Red Hat

How to set static routes for packets, within the same Network?

I have three systems A,B,C. I want to configure A in such a way that all packets from A to C goes via B. I tried: 1. ip route add 'ip of C' via 'ip of B' 2. route add -net 'net address' netmask gw 'ip of B' These commands work initially when I try a ping or traceroute and expire after... (2 Replies)
Discussion started by: kanak
2 Replies

2. SCO

Static routes in SCO

Hi, Just a question of thought. Why one needs to add static routes on Unix servers ? If I had ethernet card, it already has the settings for gateway for incoming and outgoing requests. We donot have to explicitly set the route it should take. Then what is the use... (3 Replies)
Discussion started by: dextergenious
3 Replies

3. UNIX for Dummies Questions & Answers

How does unix system administration, unix programming, unix network programming differ?

How does unix system administration, unix programming, unix network programming differ? Please help. (0 Replies)
Discussion started by: thulasidharan2k
0 Replies

4. UNIX for Dummies Questions & Answers

Routes being automatically added

Hello, I have two AIX 5.3 servers that are supposedly set up exactly the same. The problem I am having is on one of the servers, it seems dynamic routes are being added mysteriously and non-periodically. This only happens on one server and not the other. Also, there doesn't seem to be a specific... (1 Reply)
Discussion started by: Conutmonky
1 Replies

5. AIX

Static Routes question

I added a static route through smit using: Communications applications and Services ==> TCIP/IP ==> Further Configuration ==> Static Routes ==> Add a Static Route ==> Route Type of host Filled in Destination Address, Default Gateway Address and Network Interface of en0. This... (2 Replies)
Discussion started by: jyoung
2 Replies

6. IP Networking

How to delete some ipv6 routes?

Hi, How can i delete the following routes on my OpenBSD 4.1 system? # route -n show (including only relevant ipv6-routes) Internet6: Destination Gateway Flags Refs Use Mtu Interface ::/104 ::1 UGRS 1 0 ... (1 Reply)
Discussion started by: phalcos
1 Replies

7. Solaris

adding routes in Solaris

Solaris Guru's What is the proper way to add routes in the routing table so after a node reboot the routes will not be lost. I understand the /etc/defaultrouter for the default router and the <route add> command but using this command routes will be removed once the node reboots. Thanks (7 Replies)
Discussion started by: Brad_52000
7 Replies

8. Solaris

Where are routes stored ?

Hi there When adding a route (or indeed deleting a route) which file is amended ? I am moving a box from one network to another and when it starts up it tries to connect run 'add net 192.x.x.x' etc etc ...but i dont want it to do that where do I edit these route additions cheers (5 Replies)
Discussion started by: hcclnoodles
5 Replies

9. Debian

Setting Routes and such

Ok, I made changes to my routing tables..... which file do I modify to make the routes initialize correctly when the machine boots up? I work with all flavours of Unix/Linux... but this is an older box... Linux, Release 2.2.14-5.0. I did a grep for the default route in /etc, but didnt find... (2 Replies)
Discussion started by: djsal
2 Replies

10. UNIX for Dummies Questions & Answers

How to add 2 gateway routes?

I need some help adding routes in sco. I am using SCO Openserver 5.0.4. Basically I have 2 gateways here. The first is 10.15.1.1 and allows me access to the rest of the computers in the office and in other offices. The other gateway is 10.15.10.2 and is the sonicwall that will allow access... (3 Replies)
Discussion started by: cstovall
3 Replies
Login or Register to Ask a Question