Login or Register to Ask a Question and Join Our Community


HP-UX

HP-UX 10.20 Network Configure

Login to Discuss or Reply to this Discussion in Our Community

 
Thread Tools Search this Thread
Operating Systems HP-UX HP-UX 10.20 Network Configure
# 1  
Old 04-20-2007
Data HP 9000 LAN configure??
Hi
I'm new about UNIX, but I've to use a HP9000 with HP-UX 10.20 workstation. I'm trying to configure the network, I've configured the file /etc/rc.conf.d/netconf with my IP address and the right gateway, so the HP9000 is on the net, I've tried a ping. But now I've a problem I can't start hte CDE, because after the login the desktop doesn't appear, if I disconnect the LAN cable after few seconds the desktop is loaded but HP9000 give this message: "Unable to initialize or connect the Desktop messaging systems. Check your $HOME/.dt/errorlog for more information.".
Please help.

Thanks
GofMass
# 2  
Old 04-20-2007
HP-UX 10.20 Network Configure
Hi
I'm new about UNIX, but I've to use a HP9000 with HP-UX 10.20 workstation. I'm trying to configure the network, I've configured the file /etc/rc.conf.d/netconf with my IP address and the right gateway, so the HP9000 is on the net, I've tried a ping. But now I've a problem I can't start hte CDE, because after the login the desktop doesn't appear, if I disconnect the LAN cable after few seconds the desktop is loaded but HP9000 give this message: "Unable to initialize or connect the Desktop messaging systems. Check your $HOME/.dt/errorlog for more information.".
Please help.

Thanks
GofMass
# 3  
Old 04-21-2007
Please do not cross-post. I have merged the threads.
# 4  
Old 04-23-2007
Do you have a bad /etc/hosts file ? Check it.

Regards, Kaps
# 5  
Old 04-24-2007
Please try it with "sam" as well, the system administration tool.
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Solaris

Configure Solaris zone on new network

Hi, I have a Solaris 10 zone which I need to configure on a new network. I have configured the new IP on the zone itself and I can ping the interface from a node on the same network, but not from another network. Basically I need to know how to route the traffic from the zone to it's... (3 Replies)
Discussion started by: sparcman
3 Replies

2. Solaris

Configure network interface for Solaris 10

Hi, I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface. Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies

3. Solaris

Configure a network printer on solaris

Hi, guys, recently my os changed to solaris 10, and i want to share the printer with another computer whose os is also solaris. Is there anyone could give me a hint to fix this problem. lpadmin -p hp5200 -v /dev/null -A write -n... (1 Reply)
Discussion started by: papertiger
1 Replies

4. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies

5. Hardware

Slackware 13.1 can't configure two network cards

Hello everybody, I'm having troubles with Slackware 13.1 and network cards. I have one on-board Ethernet card (which is recognized and works okay) and a PCI Ethernet card (which is also recognized, but doesn't appear in 'ifconfig -a'). If i run a 'lspci', i can see the kernel recognized the... (5 Replies)
Discussion started by: semash!
5 Replies

6. Solaris

Configure ILOM from network

HI, Is it possible to set up ILOM from the ethernet terminal. I 'm at remote location from server so would like to know if i can configure it remotely I'm able to access my server via ssh terminal. (3 Replies)
Discussion started by: fugitive
3 Replies

7. Solaris

how to configure my network to use the internet

i have a router from my isp provider 02. my internet works fine in windows but i am unable to use internet in solaris. when i tried ifconfig command i was able to see the lo0 which is my laoopback adapter. pls can someone advice. (7 Replies)
Discussion started by: seyiisq
7 Replies

8. Solaris

how to configure network in solaris 10?

Hi..i have installed solaris 10 on vmware. I m not able connect to internet. pls help in detail. how to solve the problem. During the installation i have put no DHCP. cofigured manually ( Ip 192.168.1.9) default gateway 192.168.1.1 . (3 Replies)
Discussion started by: johnavery
3 Replies

9. UNIX for Dummies Questions & Answers

Need help to configure routing on home network

I have a Windows laptop and a Sparc desktop. I'm trying to toy around with routing. If have always on broadband from BT. My router ipaddress is: 192.168.1.1 This router uses DHCP. My Laptop Ip is as follows: Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . :... (2 Replies)
Discussion started by: Kongowea
2 Replies

10. UNIX for Dummies Questions & Answers

How to configure a network workstation to a standalone?

Hi, I have a networked ultra 5 workstation(using NIS) that I would like to be able to : 1. Reconfigure to standalone workstation, 2. and be able to switch back to a network workstation when the needs required. Please advise. Ryan (5 Replies)
Discussion started by: ryantk
5 Replies
Login or Register to Ask a Question